MC10EL34, MC100EL34
Table 8. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0 V; VEE = โ5.0 V (Note 1))
โ40ยฐC
25ยฐC
85ยฐC
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE Power Supply Current
39
39
42 mA
VOH Output HIGH Voltage (Note 2)
โ1085 โ1005 โ880 โ1025 โ955 โ880 โ1025 โ955 โ880 mV
VOL Output LOW Voltage (Note 2)
โ1830 โ1695 โ1555 โ1810 โ1705 โ1620 โ1810 โ1705 โ1620 mV
VIH Input HIGH Voltage (Single-Ended) โ1165
โ880 โ1165
โ880 โ1165
โ880 mV
VIL Input LOW Voltage (Single-Ended) โ1810
โ1475 โ1810
โ1475 โ1810
โ1475 mV
VBB Output Voltage Reference
โ1.38
โ1.26 โ1.38
โ1.26 โ1.38
โ1.26 V
VIHCMR Input HIGH Voltage Common Mode โ2.8
Range (Differential Configuration)
(Note 3)
โ0.4 โ2.8
โ0.4 โ2.8
โ0.4 V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / โ0.5 V.
2. Outputs are terminated through a 50ฤW resistor to VCC โ 2.0 V.
3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V.
Table 9. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = โ5.0 V (Note 1))
โ40ยฐC
25ยฐC
85ยฐC
Symbol
Characteristic
fmax Maximum Toggle Frequency
Min Typ Max Min Typ Max Min Typ Max Unit
1.1
1.1
1.1
GHz
tPLH Propagation
tPHL
CLK to Q0
Delay to
CLK to Q1,2
Output
MR to Q
ps
960
1200 960
1200 970
1210
900
1140 900
1140 910
1150
750
1060 750
1060 790
1090
tSKEW
tJITTER
tS
tH
tRR
VPP
tr
tf
Within-Device Skew (Note 2)
Cycle-to-Cycle Jitter
Setup Time EN
Hold Time EN
Set/Reset Recovery
Input Swing (Note 3)
Output Rise/Fall Times Q
(20% โ 80%)
100
100
100
ps
1.0
1.0
1.0
ps
400
400
400
ps
250
250
250
ps
400 200
400 200
400 200
ps
150
1000 150
1000 150
1000 mV
225
475 225
475 225
475 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary +0.06 V / โ0.5 V.
100 Series: VEE can vary +0.8 V / โ0.5 V.
2. Within-device skew is defined as identical transitions on similar paths through a device.
3. VPPmin is minimum input swing for which AC parameters guaranteed. The device has a DC gain of โ40.
www.onsemi.com
5