MGA-665P8 View Datasheet(PDF) - HP => Agilent Technologies
Part Name
Description
Manufacturer
MGA-665P8 Datasheet PDF : 14 Pages
| |||
3. MGA-665P8 Electrical Specifications
TA = 25°C, DC Bias for RF Parameter is VD = 3.0 V (unless otherwise specified)
Symbol
Parameter and Test Condition
Units
VC
Control Voltage
V
ID
Device Current
mA
ID (Off)
Off current
VC = 3 V
µA
Gtest[7]
Gain
Freq = 5.25 GHz dB
NFtest[7]
Noise Figure
Freq = 5.25 GHz dB
OIP3test[7,8] Output Third Order Intercept Point
Freq = 5.25 GHz dBm
P1dBtest[7] Output Power at 1dB Gain Compression Freq = 5.25 GHz dBm
Psattest[7] Output Power at Saturation
Freq = 5.25 GHz dBm
IRLtest[7]
Input return Loss
Freq = 5.25 GHz dB
ORLtest[7] Output Return Loss
Freq = 5.25 GHz dB
Ga[8]
Associated Gain at NFo
Freq = 0.9 GHz dB
Freq = 2.4 GHz
Freq = 3.5 GHz
Freq = 5.25 GHz
Freq = 5.8 GHz
NFo[8]
Optimum Noise Figure
(Tuned for Lowest Noise Figure)
Freq = 0.9 GHz dB
Freq = 2.4 GHz
Freq = 3.5 GHz
Freq = 5.25 GHz
Freq = 5.8 GHz
OIP3[8,9]
Output Third Order Intercept Point at NFo Freq = 0.9 GHz dBm
Freq = 2.4 GHz
Freq = 3.5 GHz
Freq = 5.25 GHz
Freq = 5.8 GHz
P1dB[8]
Output Power at 1 dB Gain Compression Freq = 0.9 GHz dBm
Point at NFo
Freq = 2.4 GHz
Freq = 3.5 GHz
Freq = 5.25 GHz
Freq = 5.8 GHz
Min. Typ.
Max.
-
ON: 0–1 V -
Off: 2–3 V
18.2 20.5
23.8
-
180
220
14.5 16
17.5
-
1.45
1.9
16.5 18.2
-
-
11.4
-
-
15
-
-
18
-
-
20
-
-
22.58
-
18.42
16.99
16.00
17.16
-
1.30
-
1.18
1.36
1.45
1.44
-
21.26
-
19.02
17.30
18.10
17.89
-
8.62
-
7.41
6.89
7.80
8.32
Notes:
7. Measurements obtained using production test board described in Figure 5, which represents a trade-off between optimal OIP3, P1dB, Gain and NF.
Circuit losses have been de-embedded from actual measurements.
8. Measurements obtained using test fixture with input tuned for low noise figure. Gain, OIP3 and P1dB were measured at this tuned condition. Tuner
and fixture losses have been de-embedded from actual measurements. The supply is connected to ground via a bypass capacitor. The OIP3 is
approximately 3 dB lower without this bypass capacitor.
9. OIP3 test condition: Pin = -20 dBm, Df = f1 – f2 = 10 MHz.
3
Share Link: 