CY7C1461AV33-100AXC View Datasheet(PDF) - Cypress Semiconductor
Part Name
Description
Manufacturer
CY7C1461AV33-100AXC
Cypress Semiconductor
CY7C1461AV33-100AXC Datasheet PDF : 29 Pages
| |||
CY7C1461AV33
CY7C1463AV33
CY7C1465AV33
provides byte write capability that is described in the truth
table. Asserting the Write Enable input (WE) with the selected
Byte Write Select input will selectively write to only the desired
bytes. Bytes not selected during a byte write operation will
remain unaltered. A synchronous self-timed write mechanism
has been provided to simplify the write operations. Byte write
capability has been included in order to greatly simplify
Read/Modify/Write sequences, which can be reduced to
simple byte write operations.
Because the CY7C1461AV33/CY7C1463AV33/CY7C1465AV33
is a common I/O device, data should not be driven into the
device while the outputs are active. The Output Enable (OE)
can be deasserted HIGH before presenting data to the DQs
and DQPX inputs. Doing so will tri-state the output drivers. As
a safety precaution, DQs and DQPX are automatically
tri-stated during the data portion of a write cycle, regardless of
the state of OE.
Burst Write Accesses
The CY7C1461AV33/CY7C1463AV33/CY7C1465AV33 has
an on-chip burst counter that allows the user the ability to
supply a single address and conduct up to four Write opera-
tions without reasserting the address inputs. ADV/LD must be
driven LOW in order to load the initial address, as described
in the Single Write Access section above. When ADV/LD is
driven HIGH on the subsequent clock rise, the Chip Enables
(CE1, CE2, and CE3) and WE inputs are ignored and the burst
counter is incremented. The correct BWX inputs must be
driven in each cycle of the burst write, in order to write the
correct bytes of data.
ZZ Mode Electrical Characteristics
.
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, and CE3, must remain inactive
for the duration of tZZREC after the ZZ input returns LOW.
Parameter
IDDZZ
tZZS
tZZREC
tZZI
tRZZI
Description
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
ZZ active to sleep current
ZZ Inactive to exit sleep current
Test Conditions
ZZ > VDD – 0.2V
ZZ > VDD – 0.2V
ZZ < 0.2V
This parameter is sampled
This parameter is sampled
Min.
2tCYC
0
Max.
100
2tCYC
2tCYC
Unit
mA
ns
ns
ns
ns
Truth Table[2,3,4,5,6,7,8]
Operation
Deselect Cycle
Address
Used CE1 CE2 CE3 ZZ ADV/LD WE BWX OE
None H X X L
L
XX X
CEN CLK
DQ
L L->H Tri-State
Deselect Cycle
None X X H L
L
XX X
L L->H Tri-State
Deselect Cycle
None X L X L
L
XX X
L L->H Tri-State
Continue Deselect Cycle
None X X X L
H
XX X
L L->H Tri-State
Read Cycle (Begin Burst)
External L H L L
L
HX L
L L->H Data Out (Q)
Read Cycle (Continue Burst)
Next X X X L
H
XX L
L L->H Data Out (Q)
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. BWx = L signifies at least one Byte Write Select is active, BWx = Valid signifies that the desired byte write
selects are asserted, see truth table for details.
3. Write is defined by BWX, and WE. See truth table for Read/Write.
4. When a write cycle is detected, all I/Os are tri-stated, even during byte writes.
5. The DQs and DQPX pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
6. CEN = H, inserts wait states.
7. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQPX = Tri-state when OE
is inactive or when the device is deselected, and DQs and DQPX = data when OE is active.
Document #: 38-05356 Rev. *E
Page 10 of 29
[+] Feedback
Share Link: 