ADUM1241 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADUM1241 Datasheet PDF : 24 Pages
| |||
Data Sheet
ADuM1240/ADuM1241/ADuM1245/ADuM1246
APPLICATIONS INFORMATION
PCB LAYOUT
The ADuM1240/ADuM1241/ADuM1245/ADuM1246 digital
isolators require no external interface circuitry for the logic
interfaces. Power supply bypassing is strongly recommended at
both the input and output supply pins: VDD1 and VDD2 (see
Figure 27). Maintain the capacitor value between 0.01 μF and
0.1 μF and for best results, ensure that the total lead length
between both ends of the capacitor and the input power supply
does not exceed 20 mm.
With proper PCB design choices, these digital isolators readily
meet CISPR 22 Class A (and FCC Class A) emissions standards,
as well as the more stringent CISPR 22 Class B (and FCC Class B)
standards in an unshielded environment. Refer to AN-1109 for
PCB related electromagnetic interference (EMI) mitigation
techniques, including board layout and stack up issues.
VDD1
GND1
NIC
NIC
VIA/VOA
VIB
EN1
NIC
NIC
GND1
VDD2
GND2
NIC
NIC
VOA/VIA
VOB
EN2
NIC
NIC
GND2
NIC = NOT INTERNALLY CONNECTED.
Figure 27. Recommended PCB Layout, 20-Lead SSOP (RS-20)
VDD1
VIA/VOA
VIB
GND1
VDD2
VOA/VIA
VOB
GND2
Figure 28. Recommended PCB Layout, 8-Lead SOIC (R-8)
For applications involving high common-mode transients, it is
important to minimize board coupling across the isolation barrier.
Furthermore, design the board layout so that any coupling that
does occur equally affects all pins on a given component side.
Failure to ensure this equal capacitive coupling of pins can
cause voltage differentials between pins exceeding the absolute
maximum ratings of the device, thereby leading to latch-up or
permanent damage.
PROPAGATION DELAY RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The input to
output propagation delay time for a high to low transition can
differ from the propagation delay time of a low to high transition.
INPUT (VIx)
OUTPUT (VOx)
tPLH
tPHL
50%
50%
Figure 29. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values, and an indication of how
accurately the timing of the input signal is preserved.
Channel to channel matching refers to the maximum amount
the propagation delay differs between channels within a single
component of the ADuM1240/ADuM1241/ADuM1245/
ADuM1246.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM1240/
ADuM1241/ADuM1245/ADuM1246 components operating
under the same conditions.
DC CORRECTNESS AND LOW POWER OPERATION
Standard Operating Mode
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder using the
transformer. The decoder is bistable and is, therefore, either set
or reset by the pulses, indicating input logic transitions. When
refresh and watchdog functions are enabled, by pulling EN1 and
EN2 low, in the absence of logic transitions at the input for more
than ~140 μs, a periodic set of refresh pulses, indicative of the
correct input state, is sent to ensure dc correctness at the output. If
the decoder receives no internal pulses of more than approximately
200 μs, the device assumes that the input side is unpowered or
nonfunctional, in which case, the isolator watchdog circuit
forces the output to a default state. The default state is either high,
as in the ADuM1240 and ADuM1241 versions, or low, as in the
ADuM1245 and ADuM1246 versions.
Low Power Operating Mode
For the lowest power consumption, disable the refresh and
watchdog functions of the ADuM1240/ADuM1241/ADuM1245/
ADuM1246 by pulling EN1 and EN2 to logic high. These control
pins must be set to the same value on each side of the component
for proper operation.
In this mode, the current consumption of the chip drops to the
microampere range. However, be careful when using this mode,
because dc correctness is no longer guaranteed at startup. For
example, if the following sequence of events occurs:
1. Power is applied to Side 1.
2. A high level is asserted on the VIA input.
3. Power is applied to Side 2.
The high on VIA is not automatically transferred to the Side 2
VOA, and there can be a level mismatch that is not corrected until a
transition occurs at VIA. When power is stable on each side, and a
transition occurs on the input of the channel, the input and output
state of that channel is correctly matched. This contingency can
be resolved in several ways, such as sending dummy data, or
toggling refresh on for a short period to force synchronization after
turn on.
Rev. B | Page 17 of 24
Share Link: 