AD8176(2007) Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

Fabricante

AD8176
(Rev.:2007)

475 MHz, Triple 16 × 9 Video Crosspoint Switch

Analog Devices 

Preliminary Technical Data

THEORY OF OPERATION

The AD8176 is a non-blocking crosspoint with 16 RGB input

channels and 9 RGB output channels. Architecturally, the

AD8176 is a differential-in, differential-out crosspoint suited

for middle-of-CAT5-run applications. Furthermore, its

differential-in, differential-out gain of +4 and its decoded H and

V sync outputs make it the ideal solution for driving a monitor

directly. The ability to set the output common-mode (CM) and

black level through external pins offers additional flexibility.

Processing of CM voltage levels is achieved by placing the

AD8176 in either of its two operation modes. In the first

operation mode (CMENC low), the input CM of each RGB

differential pair (possibly present either in the form of sync-on

CM signaling or noise) is removed through the switch, and the

output CM is set to a global reference voltage via the

VOCM_CMENCOFF analog input. In this mode the AD8176

behaves as a traditional differential-in, differential-out switch. If

sync-on CM signaling is present at the differential RGB inputs,

then the H and V outputs represent decoded syncs. In the

second operation mode (CMENC high), input sync-on CM

signaling is propagated through the switch with unity gain. In

this mode, the overall output CM is set to a global reference

voltage via the VOCM_CMENCON analog input. Note that in

both operation modes, the overall input CM is blocked through

the switch.

Input pin VBLK defines the black level of the positive output

phase. The combination of VBLK and VOCM_CMENCOFF

allows the user to position the positive and negative output

phases anywhere in the allowable output voltage range, thus

maximizing output headroom usage.

The switch is organized into nine 16:1 RBG multiplexers, with

each being responsible for connecting an RGB input channel to

its respective RGB output channel. Decoding logic selects a

single input (or none) in each multiplexer and connects it to its

respective output. Feedback around each multiplexer realizes a

closed-loop differential-in, differential-out gain of +2 in the core.

Each differential RGB input channel is buffered by a differential

receiver, which is capable of accepting input CM voltages

extending all the way to either supply rail. Excess closed-loop

receiver bandwidth reduces the receiver’s effect on the overall

device bandwidth. Feedback around each differential receiver

realizes a gain of +2 yielding an overall differential-in,

differential-out crosspoint gain of +4. A separate loop realizes a

closed-loop common-mode gain of +1.

The output stage is designed for fast slew rate and settling time

while driving a series-terminated CAT5 cable. Unlike

competing multiplexer designs, the small signal bandwidth

closely approaches the large signal bandwidth.

AD8176

The outputs of the AD8176 can be disabled to minimize on-

chip power dissipation. When disabled, there is only a

common-mode feedback network of 3.33 kΩ between the

differential outputs. This high impedance allows multiple ICs to

be bussed together without additional buffering. Care must be

taken to reduce output capacitance, which can result in

overshoot and frequency-domain peaking. A series of internal

amplifiers drive internal nodes such that wideband high

impedance is presented at the disabled output, even while the

output bus experiences fast signal swings. When the outputs are

disabled and driven externally, the voltage applied to them

should not exceed the valid output swing range for the AD8176

in order to keep these internal amplifiers in their linear range of

operation. Applying excessive differential voltages to the

disabled outputs can cause damage to the AD8176 and should

be avoided (see the Absolute Maximum Ratings section of this

data sheet for guidelines).

The connectivity of the AD8176 is controlled by a flexible TTL-

compatible logic interface. Either parallel or serial loading into a

first rank of latches preprograms each output. A global update

signal moves the programming data into the second rank of

latches, simultaneously updating all outputs. In serial mode, a

serial-out pin allows devices to be daisy-chained together for a

single-pin programming of multiple ICs. A power-on reset pin

is available to avoid bus conflicts by disabling all outputs. This

power-on reset clears the second rank of latches, but does not

clear the first rank of latches. A broadcast parallel programming

feature is available in parallel mode to quickly clear the first

rank. In serial-mode, preprogramming individual inputs is not

possible and the entire shift register needs to be flushed. A

global chip-select pin gates the input clock and the global

update signal to the second rank of buffers.

The AD8176 can operate on a single +5 V supply, powering

both the signal path (with the VPOS/VNEG supply pins) and

the control logic interface (with the VDD/DGND supply pins).

Split supply operation is possible with ±2.5 V supplies in order

to easily interface to ground-referenced video signals. In this

case, a flexible logic interface allows the control logic supplies

(VDD/DGND) to be run off +5 V/0 V to +3.3 V/0 V while the

analog core remains on split supplies. Additional flexibility in

the analog output common-mode level (VOCM_CMENCOFF)

and output black level (VBLK) facilitates operation with

unequally split supplies. If +3 V/−2 V supplies to +2 V/−3 V

supplies are desired, the output CM can still be set to 0 V for

ground-referenced video signals.

Rev. PrA | Page 21 of 32

Share Link: