AD7994-0 Ver la hoja de datos (PDF) - Analog Devices

Número de pieza

componentes Descripción

Fabricante

AD7994-0

4-Channel, 10- and 12-Bit ADCs with I2C-Compatible Interface in 16-Lead TSSOP

Analog Devices 

CIRCUIT INFORMATION

The AD7993/AD7994 are low power, 10- and 12-bit, single-

supply, 4-channel A/D converters, respectively. The parts can

be operated from a 2.7 V to 5.5 V supply.

The AD7993/AD7994 provide the user with a 4-channel

multiplexer, an on-chip track-and-hold, an A/D converter, an

on-chip oscillator, internal data registers, and an I2C-compatible

serial interface, all housed in a 16-lead TSSOP package that

offers the user considerable space-saving advantages over

alternative solutions. The AD7993/AD7994 require an external

reference in the range of 1.2 V to VDD.

The AD7993/AD7994 normally remain in a power-down state

while not converting. When supplies are first applied, the parts

come up in a power-down state. Power-up is initiated prior to

a conversion, and the device returns to shutdown upon com-

pletion of the conversion. Conversions can be initiated on the

AD7993/AD7994 by pulsing the CONVST signal, using an

automatic cycle interval mode, or using a command mode

where wake-up and a conversion occurs during a write address

function (see the Modes of Operation section). When the con-

version is complete, the AD7993/AD7994 again enter shutdown

mode. This automatic shut-down feature allows power saving

between conversions. Any read or write operations across the

I2C interface can occur while the devices are in shutdown.

CONVERTER OPERATION

The AD7993/AD7994 are successive approximation analog-to-

digital converters based around a capacitive DAC. Figure 18 and

Figure 19 show simplified schematics of an ADC during the

acquisition and conversion phase, respectively. Figure 18 shows

an ADC during the acquisition phase. SW2 is closed and SW1

is in Position A. The comparator is held in a balanced condition

and the sampling capacitor acquires the signal on VINx.

CAPACITIVE

DAC

VIN

AGND

A

SW1

B

SW2

CONTROL

LOGIC

COMPARATOR

Figure 18. ADC Acquisition Phase

AD7993/AD7994

When the ADC starts a conversion, as shown in Figure 19, SW2

opens and SW1 moves to Position B, causing the comparator to

become unbalanced. The input is disconnected once the con-

version begins. The control logic and the capacitive DAC are

used to add and subtract fixed amounts of charge from the

sampling capacitor to bring the comparator back into a

balanced condition. When the comparator is rebalanced, the

conversion is complete. The control logic generates the ADC

output code. Figure 20 shows the ADC transfer function.

CAPACITIVE

DAC

VIN

AGND

A

SW1

B

SW2

CONTROL

LOGIC

COMPARATOR

Figure 19. ADC Conversion Phase

ADC Transfer Function

The output coding of the AD7993/AD7994 is straight binary.

The designed code transitions occur at successive integer LSB

values—that is, 1 LSB, 2 LSB, and so on. The LSB size is

REFIN/1024 for the AD7993 and REFIN/4096 for the AD7994.

Figure 20 shows the ideal transfer characteristic for the

AD7993/AD7994.

111...111

111...110

111...000

011...111

000...010

000...001

000...000

AD7993 1LSB = REFIN/1024

AD7994 1LSB = REFIN/4096

AGND + 1LSB

+REFIN – 1LSB

ANALOG INPUT

0V TO REFIN

Figure 20. AD7993/AD7994 Transfer Characteristic

Rev. 0 | Page 15 of 32

Share Link: