HSC-AT11K-A10 Ver la hoja de datos (PDF) - HIROSE ELECTRIC
Número de pieza
componentes Descripción
Fabricante
HSC-AT11K-A10 Datasheet PDF : 5 Pages
| |||
HSC-AT11 Series●SC Type Fixed Attenuators(for single mode)
■Product Specifications
●UPC Polishing type : Return Loss ≥ 50dB
●APC Polishing type : Return Loss ≥ 60dB
Ratings
Operating temperature range
Max. Input Power
-40°C to +75°C
250mW
Storage temperature range
Fiber type
-40°C to +85°C
SMF
Item
Polishing type
Attenuation
Return Loss
Input power
Controlled Operating
Environment
Uncontrolled Operating
Environment
Non-Operating
Environment
Humidity/Condensation
Cycling Test
Water Immersion
Vibration Test
Test Method (Telcordia GR-910-CORE)
Specifications
UPC
APC
Measurement at a point within wavelength of 1310±30 nm See the attenuation table on the next page
and a point within wavelength of 1550±30 nm.
≥50dB
≥60dB
Input power : 250mW(LD)
Wavelength : 1470nm
Time : 100 hours
Temperature : -5 to 50 ℃
Time : 182.5 hours
Humidity : 15 to 90 %
Temparature : -40 to 75 ℃
Cycles : 21 cycles ( 8h/cycle)
Low-Temperture Exposure and Thermal Shock
Temperature
: 23 → −40 → −40 → 23
Time
: 2.1h 72h 4min
High-Temperture Exposure and Thermal Shock
Temperature
: 23 → 70 → 70 → 23
Time
: 1.6h 72h 5min
High Relative Humidity Exposure
Temperature
: 23 → 40 → 40 → 23
Time
: 0.6h 96h 0.6h
Humidity
: 90 to 95 %
Temperature
: -10 to 65 ℃
Humidity
: 90 to 100 %
Cycles
: 14 cycles(12h/cycle)
Temperature
: 43 ℃
Time
: 168 h
Water
: PH 5.5
Frequency range : 10 to 55 Hz
Amplitude
: 1.52mm
Time
: 2 hours in each 3 axis
1)After test, change in attenuation (fluctuation)
and return loss shall be as follows.
attenuation : ≤0.5dB
return loss ≥50dB
2)No distortion, package cracks, hardening or
softening of materials, and also no damage to
the attenuation element.
Side Pull Load
Angle : 90 °
Load : 12.25 N
1)During, after test, change in attenuation
(fluctuation) and return loss shall be as follows.
attenuation : ≤0.5dB
return loss ≥50dB
2)No distortion, package cracks, hardening or
softening of materials, and also no damage to
the attenuation element.
Cable Retention
Load : 19.6N
Durability
200 times
Drop the tested components from 1.8 m hight to the
Impact Test
concrete floor.
8 times in each 3 axis
Note) APC polishing type isn’t compatible with UPC polishing type.
1)After test, change in attenuation (fluctuation)
and return loss shall be as follows.
attenuation : ≤0.5dB
return loss ≥50dB
2)No distortion, package cracks, hardening or
softening of materials, and also no damage to
the attenuation element.
82
Share Link: 