MC10EP105 Ver la hoja de datos (PDF) - ON Semiconductor
Número de pieza
componentes Descripción
Fabricante
MC10EP105 Datasheet PDF : 11 Pages
| |||
MC10EP105, MC100EP105
Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 17)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
IEE
Power Supply Current VCC = −3.3 V 45
59
80
45
62
85
45
65
85 mA
VCC = −5.0 V 45
63
80
45
66
85
45
69
85
VOH
VOL
VIH
VIL
VIHCMR
Output HIGH Voltage (Note 18)
Output LOW Voltage (Note 18)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 19)
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
−1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV
−1225
−880 −1225
−880 −1225
−880 mV
−1945
−1625 −1945
−1625 −1945
−1625 mV
VEE+2.0
0.0
VEE+2.0
0.0
VEE+2.0
0.0
V
IIH
Input HIGH Current
IIL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
17. Input and output parameters vary 1:1 with VCC.
18. All loading with 50 W to VCC − 2.0 V.
19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential
input signal.
Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 20)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
fmax
Maximum Frequency
(See Figure 4 Fmax/JITTER)
>3
>3
>3
GHz
tPLH,
tPHL
Propagation Delay to
Output Differential
175 250 325 200 275 350 225 300 375 ps
tSKEW
Within Device Skew
Device to Device Skew (Note 21)
10
50
10
50
15
50 ps
tJITTER
VPP
Cycle−to−Cycle Jitter
(See Figure 4 Fmax/JITTER)
Input Voltage Swing
(Differential Configuration)
0.2 < 1
0.2 < 1
0.2 < 1 ps
150 800 1200 150 800 1200 150 800 1200 mV
tr
Output Rise/Fall Times
tf
(20% − 80%)
Q 100 150 200 120 170 220 150 200 250 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
20. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V.
21. Skew is measured between outputs under identical transitions.
http://onsemi.com
7
Share Link: 