GX-H12AI Ver la hoja de datos (PDF) - Panasonic Corporation
Número de pieza
componentes Descripción
Fabricante
GX-H12AI Datasheet PDF : 16 Pages
| |||
GX-F/H Rectangular-shaped Inductive Proximity Sensor
SERIES
796
SENSING CHARACTERISTICS (TYPICAL)
FIBER
SENSORS
GX-15 (Long sensing range) type
Sensing field
Standard sensing object Standard sensing object
Iron sheet 30 × 30 × t 1 mm Iron sheet 30 × 30 × t 1 mm
1.181 × 1.181 × t 0.039 in 1.181 × 1.181 × t 0.039 in
10
ℓ
0.394
L
ℓ
Top
sensing
Front
L
sensing
5
0.197
Correlation between sensing object size and sensing range
Sensing object Sensing object
a × a mm a × a in a × a mm a × a in
10
0.394
L
t 1mm L
t 0.039 in
Front sensing
t 1mm t 0.039 in
Top sensing Iron
Stainless steel
(SUS304)
5
0.197
Brass
Aluminum
As the sensing object size becomes smaller than
the standard size (iron sheet 30 × 30 × t 1 mm
1.181 × 1.181 × t 0.039 in), the sensing range
shortens as shown in the left figure.
0
10
5
0
5
10
0
10
20
30
40
0.394 0.197
0.197 0.394
0.394 0.787 1.181 1.575
Left
Center
Right
Sensing object side
Operating point ℓ (mm in)
length a (mm in)
PRECAUTIONS FOR PROPER USE
Refer to p.1579~ for general precautions.
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
Mounting
GX-6 type
• Use the optional sensor mounting bracket when
installing.
GX-8 type
<When using MS-GXL8-4 (Optional)>
• Make sure to use a M3
(length: 12 mm 0.472 in or
more) truss head screw
(accessory for MS-GXL8-4).
The tightening torque
should be 0.7 N·m or less.
Do not use a flat head
screw or a pan head
screw.
GX-12 type
M3 (length 12 mm 0.472 in) truss head
screw (Accessory for MS-GXL8-4)
Sensor mounting bracket
MS-GXL8-4 (Optional)
M3 × 0.5 mm 0.020 in tapped hole
(Depth: 8 mm 0.315 in or more)
or ø3.4 mm ø0.134 in thru-hole
11.5 mm 0.453 in
The nut, washer, and spring
washer are attached with the
MS-GXL8-4.
ø2.4 mm ø0.094 in hole
(Depth: 3 mm 0.118 in or more)
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
<When using MS-GX6-1 (Optional / recommended)>
• To mount the sensor with
a nut, the mounting hole
diameter should be
ø3.4 mm ø0.134 in.
1 Insert the sensor into the
bracket as shown on the
right.
2 Push the sensor until the
bracket hook is lodged in
the groove on the upper
portion of the sensor.
3 Fix the bracket in place
with M3 pan head screw.
Cable Hook
Groove
ø2.4 mm
ø0.094 in hole
(Depth: 3 mm
0.118 in or more)
M3 pan head screw
(Purchase separately.)
Sensor mounting bracket
MS-GX6-1 (Optional)
M3 × 0.5 mm 0.020 in
tapped hole (Depth: 8 mm
0.315 in or more) or
ø3.4 mm ø0.134 in thru-hole
22 mm 0.866 in
No nuts, washers, or
spring washers are
attached with the
product.
Purchase separately.
• The tightening torque
should be 0.7 N·m or less.
• To mount the sensor with
a nut, the mounting hole
diameter should be
ø3.4 mm ø0.134 in.
Further, the hole in which
the boss is inserted should
be ø2.5 mm ø0.098 in and
3 mm 0.118 in, or more,
deep.
GX-15 type
• The tightening torque
should be 1 N·m or less.
<When using MS-GL6-1 (Optional) / MS-GL6-2 (Optional)>
• To mount the sensor with a nut, the mounting hole
diameter should be ø3.4 mm ø0.134 in.
• To mount the sensor with
a nut, the mounting hole
diameter should be
ø3.4 mm ø0.134 in.
M3 (length 12 mm 0.472 in or more)
pan head screw
(Purchase separately.)
M3 × 0.5 mm 0.020 in tapped hole
(Depth: 10 mm 0.394 in or more)
or ø3.4 mm ø0.134 in thru-hole
16 mm 0.630 in
No nuts, washers, or spring washers
are attached with the product.
Purchase separately.
ø2.5 mm ø0.098 in hole
(Depth: 3 mm 0.118 in or more)
M3 pan head screws or
truss head screws
Do not use flat head
screws.
M3 × 0.5 mm 0.020 in
tapped holes or ø3.4 mm
ø0.134 in thru-holes
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplifier
Built-in
Amplifier-
separated
Other
Products
GX-F/H
GXL
GL
13.6 mm
0.535 in
M3 pan head screws
(Purchase separately.)
Sensor mounting bracket
MS-GL6-1 (Optional) ø2.4 mm
0.094 in hole
(Depth: 3 mm
0.118 in or more)
M3 × 0.5 mm 0.020 in
tapped holes or
ø3.4 mm ø0.134 in thru-holes
10 mm
0.394 in
No nuts, washers, or
spring washers are
attached with the
product.
Purchase separately.
M3 pan head screw
(Purchase separately.)
Sensor mounting bracket
MS-GL6-2 (Optional)
9 mm
0.354 in
M3 × 0.5 mm 0.020 in
tapped hole or
ø3.4 mm ø0.134 in thru-holes
No nuts, washers, or
spring washers are
attached with the
product.
Purchase separately.
• When installing the long
sensing range type on iron
or stainless steel plate, put
the optional aluminum sheet
in between the sensor and
the plate.
GX-M
GX-U/GX-FU/
GX-N
No nuts, washers, or spring washers GX
are attached with the product.
Purchase separately.
MS-GXL15
(Sensor mounting bracket)
Aluminum sheet (Optional)
• MS-A15F
• MS-A15H
Share Link: 