HSDL-3602-008 Ver la hoja de datos (PDF) - Avago Technologies
Número de pieza
componentes Descripción
Fabricante
HSDL-3602-008 Datasheet PDF : 27 Pages
| |||
Electrical & Optical Specifications
Specifications hold over the Recommended Operating Conditions unless otherwise noted. Unspecified test condi-
tions can be anywhere in their operating range. All typical values are at 25ËšC and 3.3 V unless otherwise noted.
Parameter
Symbol Min. Typ.
Max. Units Conditions
Receiver
Receiver Data
Logic Low VOL
0
—
0.4
V
Output Voltage
IOL = 1.0 mA,
EI ≥ 3.6 µW/cm2,
Logic High VOH
VCC – 0.2 —
VCC
V
θ1/2 ≤ 15˚
IOH = –20 µA,
EI ≤ 0.3 µW/cm2,
θ1/2 ≤ 15˚
Viewing
2θ1/2
30
Ëš
Angle
Logic High Receiver Input
EIH
0.0036
500
mW/cm2 For in-band signals
Irradiance
≤ 115.2 kb/s[8]
0.0090
500
mW/cm2 0.576 Mb/s ≤ in-band
signals ≤ 4 Mb/s[8]
Logic Low Receiver Input
Irradiance
EIL
0.3
µW/cm2 For in-band signals[8]
Receiver Peak Sensitivity
Wavelength
λP
880
nm
Receiver SIR Pulse Width
tpw (SIR) 1
4.0
µs
Receiver MIR Pulse Width
tpw (MIR) 100
500
ns
Receiver FIR Pulse Width
tpw (FIR) 85
165
ns
190
ns
θ1/2 ≤ 15˚[10], CL = 10 pF
θ1/2 ≤ 15˚[11], CL = 10 pF
θ1/2 ≤ 15˚[12], CL = 10 pF,
VCC = 3 to 3.6 V
θ1/2 ≤ 15˚[12], CL = 10 pF,
VCC = 2.7 V
Receiver ASK Pulse Width
tpw (ASK)
1
µs
500 kHz/50% duty cycle
carrier ASK[13]
Receiver Latency Time for FIR
Receiver Latency Time for SIR
tL (FIR)
tL (SIR)
40
50
µs
20
50
µs
Receiver Rise/Fall Times
Receiver Wake Up Time
tr/f (RXD)
25
ns
tW
100
µs
[14]
Notes:
8. An in-band optical signal is a pulse/sequence where the peak wavelength, λp, is defined as 850 ≤ λp ≤ 900 nm, and the pulse characteristics are
compliant with the IrDA Serial Infrared Physical Layer Link Specification.
9. Logic Low is a pulsed response. The condition is maintained for duration dependent on pattern and strength of the incident intensity.
10. For in-band signals ≤ 115.2 kb/s where 3.6 µW/cm2 ≤ EI ≤ 500 mW/cm2.
11. For in-band signals at 1.15 Mb/s where 9.0 µW/cm2 ≤ EI ≤ 500 mW/cm2.
12. For in-band signals of 125 ns pulse width, 4 Mb/s, 4 PPM at recommended 400 mA drive current.
13. Pulse width specified is the pulse width of the second 500 kHz carrier pulse received in a data bit. The first 500 kHz carrier pulse may exceed
2 µs in width, which will not affect correct demodulation of the data stream. An ASK or DASK system using the HSDL-3602 has been shown to
correctly receive all data bits for 9 µW/cm2 ≤ EI ≤ 500 mW/cm2 incoming signal strength. ASK or DASK should use the FIR channel enabled.
14. The wake up time is the time between the transition from a shutdown state to an active state, and the time when the receiver is active and ready
to receive infrared signals.
Share Link: 