IG120-24 データシートの表示（PDF） - MicroPower Direct, LLC
部品番号
コンポーネント説明
メーカー
IG120-24 Datasheet PDF : 2 Pages
| |||
Model Selection Guide
www.micropowerdirect.com
Model
Number
Input (Supply)
Voltage (VDC)
Nom. Range
Output 1
Voltage (VDC) Current
Min. Nom. Max. (mA Max)
Current
(mA, Min)
Output 2
Voltage (VDC) Current
Min. Nom. Max. (mA Max)
Current
(mA, Min)
Output
Load
Regulation
(%)
Maximum
Capacitive
Load
(µF)
Fuse Rating
Slow-Blow
(mA)
IG120-12 12 11.6 - 12.4 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0
12
470
1,000
IG120-12W 12 9.0 - 15.0 14.0 15.0 16.0 100.0 0.0 -7.0 -8.0 -9.0 80.0 0.0
12
470
1,000
IG120-15 15 14.5 - 15.5 14.0 15.0 16.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0
18
470
1,000
IG136-15 15 14.5 - 15.5 16.5 17.0 18.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0
18
470
1,000
IG120-24 24 23.3 - 24.7 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0
12
470
1,000
The IG100 series is designed
to operate with the IGD962
IGBT driver.
Typical Connection
Notes:
1. Line regulation for model IG120-12W is given for a
VIN change of 25%.
2. Load regulation is measured from 10% load to full
load. Load regulation is specified for the primary
output (output 1). Load regulation of output 2 may
vary slightly.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. If output 2 is not used, it should be left open.
5. A short circuit fault that lasts over 10 minutes could
damage the unit due to an over temperature fault.
6. It is recommended that a fuse be used on the input of a
power supply for protection. See the Model Selection
table above for the correct rating.
Mechanical Dimensions
Connection Notes:
1. For model IG120-24, C1 is a 100 µF/65V.
2. Capacitors C1, C2 and C3 should be mounted as close
to the unit as possible. To ensure peak gate current,
these capacitors should have a low ESR.
3. The trace (or wire) between the DC/DC and the driver
circuit should be as short as possible.
4. The average output power of the driver circuit must
be lower than output power of the DC/DC.
Pin Connections
Pin Function
1
+Vin
2
Gnd
5 Vout 2
6 Common
7 Vout 1
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
Share Link: 