S4804CBI データシートの表示（PDF） - Applied Micro Circuits Corporation

部品番号

コンポーネント説明

メーカー

S4804CBI

OC-48 / 4xOC-12 / 16xOC-3 SONET/SDH FRAMER AND POS/ATM MAPPER

Applied Micro Circuits Corporation 

S4804CBI41: RHINE

STS-48 POS/ATM SONET MAPPER

Overview and Applications

Sonet/SDH Processing

The S4804 implements SONET/SDH processing and full-

duplex ATM/packet-mapping functions for STS-48/STM-16,

STS-12/STM-4, or STS-3/STM-1 data streams. It can support

either a single STS-48c/AU-4-16c or any valid combination of

STS-12c/AU-4-4c or STS-3c/AU-4 signals within an STS-48/

STM-16. The S4804 also supports 4 STS-12/STM-4 signals

(each containing a single STS-12c/AU-4-4c or 4 STS-3c/AU-

4), or 16 STS-3c/STM-1 signals each containing an STS-3c/

AU-4.

A TOH/SOH interface provides direct add/drop capability for

E1, E2, F1, and both Section and Line DCC channels. The

S4804 also includes a clear channel mode that enables the

direct transmission of system payload from the system inter-

face to the line-side interface.

On the transmit side, the S4804 generates section, line, and

path overhead. It performs framing pattern insertion (A1, A2),

scrambling, alarm-signal insertion, and generates section,

line, and path Bit Interleaved Parity (B1/B2/B3) for far-end

performance monitoring.

On the receive side, the S4804 processes section, line, and

path overhead. It performs framing (A1, A2), descrambling,

alarm detection, pointer processing, Bit Interleaved Parity

monitoring (B1/B2/B3), and error-count accumulation for

performance monitoring.

ATM Processing

When configured for ATM cell processing, the S4804’s trans-

mit ATM processor(s) will perform all necessary cell process-

ing as defined by ATM UNI3.1, ITU-T I.432.1, and I.432.2.

Product Brief Version 2.0 - January 2002

PRODUCT BRIEF

HDLC Processing

When configured for POS mode, the S4804’s HDLC proces-

sor(s) provides HDLC packet processing as defined by IETF

RFCs 1619, 1662 and 2615. In addition, the S4804 optionally

performs scrambling (X43+1).

Direct Map Mode

Direct Map Mode allows to map any protocol directly into the

Sonet/SDH Synchronous Payload Envelope, by-passing the

ATM and HDLC processing circuitry.

Automatic Protection Switching

The S4804 provides APS input and output interfaces to

convey signals between two S4804 devices configured for

APS operation. This configuration supports both 1+1 and 1:1

configurations.

Line-side Interface

On the line side, the S4804 supports a 16-bit parallel

interface, operating at 155MHz for a single OC-48 optical

interface. It provides serial interfaces at either 622 MHz or

155 MHz for OC-12 and/or OC-3 optical interfaces. Mixed

OC-3 / OC-12 line rates are supported.

System Interface

The S4804 supports a 32-bit, 100-MHz system interface. For

ATM cell transfers, the S4804 supports Utopia Level 3

interface. For packet transfers, the S4804 supports

FlexBusTM interface. The S4804 also provides support for a

quad, 8-bit extension of the Utopia 3.

TYPICAL APPLICATIONS: S4804CBI - RHINE in ATM or POS System

Single STS-48 / Quad STS-12/ 16xSTS-3

POS or ATM over SONET Application

Reference

Clock

Microprocessor

Control

14 16

Control Addr Data

IP Router or ATM Switch

SONET

Line Side

Interface

SerTxD±

Fiber Optic

TX_SONETCLK_IN

P/S & S/P TX_DATA[15:0]

Transceiver SerRxD± SONET XCVR

with

RX_LOSEXT[1]

HP / Lucent

Clk Recovery RX_SONETCLK[2]

RX_DATA[15:0]

Either

Single OC-48

or

Four OC-12

or

Sixteen OC-3

For OC-48 Mode:

AMCC 3055

AMCC

RHINE

S4804CBI

TX_CLK

TX_SYS_DAT[31:0]

RX_SYS_DAT[31:0]

RX_CLK

Multi

Channel

Link Layer

Device

TOH Insertion

and Extraction

AMCC

200 Minuteman Road, Andover, MA 01810 Ph: (978) 623-0009 Fax: (978) 623-0024

Switching/

Routing

Logic

Share Link: