UPC324G2 データシートの表示（PDF） - NEC => Renesas Technology

部品番号

コンポーネント説明

メーカー

UPC324G2

LOW POWER QUAD OPERATIONAL AMPLIFIER

NEC => Renesas Technology 

µPC324

ABSOLUTE MAXIMUM RATINGS (TA = 25 °C)

Parameter

Symbol

Voltage between V+ and V–

Note 1

V+–V–

Differential Input Voltage

VID

Input Voltage

Note 2

VI

Output Voltage

Note 3

VO

Power Dissipation

C Package Note 4

PT

G2 Package Note 5

Output Short Circuit Duration

Note 6

Operating Ambient Temperature

TA

Ratings

Unit

–0.3 to +32

V

±32

V

V––0.3 to V–+32

V

V––0.3 to V++0.3

V

570

mW

550

mW

Indefinite

sec

–20 to +80

°C

Storage Temperature

Tstg

–55 to + 125

°C

Notes 1. Reverse connection of supply voltage can cause destruction.

2. The input voltage should be allowed to input without damage or destruction independent of the

magnitude of V+. Either input signal should not be allowed to go negative by more than 0.3 V. The normal

operation will establish when the both inputs are within the Common Mode Input Voltage Range of

electrical characteristics.

3. This specification is the voltage which should be allowed to supply to the output terminal from external

without damage or destructive. Even during the transition period of supply voltage, power on/off etc.,

this specification should be kept. The output voltage of normal operation will be the Output Voltage Swing

of electrical characteristics.

4. Thermal derating factor is –7.6 mW/°C when operating ambient temperature is higher than 50 °C.

5. Thermal derating factor is –5.5 mW/°C when operating ambient temperature is higher than 25 °C.

6. Pay careful attention to the total power dissipation not to exceed the absolute maximum ratings, Note

4 and Note 5.

RECOMMENDED OPERATING CONDITIONS

Parameter

Supply Voltage (Split)

Supply Voltage (V– = GND)

Symbol

MIN.

TYP.

MAX.

Unit

V±

±1.5

±15

V

V+

3

30

V

µPC324C, µPC324G2

ELECTRICAL CHARACTERISTICS (TA = 25 °C, V+ = 5 V, V– = GND)

Parameter

Input Offset Voltage

Input Offset Current

Input Bias Current

Note 7

Large Single Voltage Gain

Supply Current

Note 8

Common Mode Rejection Ratio

Supply Voltage Rejection Ratio

Output Voltage Swing

Common Mode Input Voltage Range

Output Current (SOURCE)

Output Current (SINK)

Channel Separation

Symbol

VIO

IIO

IB

AV

ICC

CMR

SVR

VO

VICM

IO SOURCE

IO SINK

RS = 0 Ω

Conditions

RL ≥ 2 kΩ

RL = ∞, IO = 0 A

RL = 2 kΩ (Connect to GND)

VIN + = +1 V, VIN– = 0 V

VIN – = +1 V, VIN+ = 0 V

VIN– = +1 V, VIN+ = 0 V, VO = 200 mV

f = 1 kHz to 20 kHz

MIN.

25

65

65

0

0

20

10

12

TYP.

±2

±5

45

100

1.0

85

100

40

20

50

120

MAX.

±7

±50

250

2

V+ – 1.5

V+ – 1.5

Unit

mV

nA

nA

V/mV

mA

dB

dB

V

V

mA

mA

µA

dB

Notes 7. Input bias currents flow out from IC. Because each currents are base current of PNP-transistor on input

stage.

8. This current flows irrespective of the existence of use.

2

Data Sheet G11763EJ4V0DS

Share Link: