ELM322P 데이터 시트보기 (PDF) - Elm Electronics
부품명
상세내역
제조사
ELM322P Datasheet PDF : 18 Pages
| |||
ELM322
Interpreting Trouble Codes
Likely the most common use that the ELM322 will
be put to is in obtaining the current Diagnostic Trouble
Codes or DTCs. Minimally, this requires that a mode
03 request be made, but first one should determine
how many trouble codes are presently stored. This is
done with a mode 01 PID 01 request as follows:
>01 01
To which a typical response might be:
41 01 81 07 65 04
The 41 01 signifies a response to our request, and
the first data byte (81) is the result that we are looking
for. Clearly there would not be 81(hex) or 129(decimal)
trouble codes if the vehicle is operational. In fact, this
byte does double duty, with the most significant bit
being used to indicate that the malfunction indicator
lamp (MIL, or ‘Check Engine’) has been turned on by
one of this module’s codes (if there are more than
one), while the other 7 bits provide the actual number
of stored codes. To determine the number of stored
codes, then, one needs to subtract 128 (or 80 hex)
from the number if it is greater than 128, and otherwise
simply read the number of stored codes directly.
The above response then indicates that there is
one stored code, and it was the one that set the MIL or
‘Check Engine’ lamp on. The remaining bytes in the
response provide information on the types of tests
supported by that particular module (see SAE
document J1979 for further information).
In this instance, there was only one line to the
response, but if there were codes stored in other
modules, they each could have provided a line of
response. To determine which module is reporting the
trouble code, one would have to turn the headers on
(ATH1) and then look at the third byte of the three byte
header for the address of the module that sent the
information.
Having determined the number of codes stored,
the next step is to request the actual trouble codes
with a mode 03 request:
>03
A response to this could be:
43 01 33 00 00 00 00
The ‘43’ in the above response simply indicates
that this is a response to a mode 03 request. The other
6 bytes in the response have to be read in pairs to
show the trouble codes (the above would be
interpreted as 0133, 0000, and 0000). Note that there
is only one trouble code here. The response has been
padded with 00’s as is required by the standard, and
the extra 0000’s do not represent actual trouble codes.
As was the case when requesting the number of
stored codes, the most significant bits of each trouble
code also contain additional information. It is easiest to
use the following table to interpret the first digit of a
trouble code as follows:
If the first hex digit received is this,
Replace it with these two characters
0 P0
1 P1
2 P2
3 P3
4 C0
5 C1
6 C2
7 C3
8 B0
9 B1
A B2
B B3
C U0
D U1
E U2
F U3
Powertrain Codes - SAE defined
“ “ - manufacturer defined
“ “ - SAE defined
“ “ - jointly defined
Chassis Codes - SAE defined
“ “ - manufacturer defined
“ “ - manufacturer defined
“ “ - reserved for future
Body Codes - SAE defined
“ “ - manufacturer defined
“ “ - manufacturer defined
“ “ - reserved for future
Network Codes - SAE defined
“ “ - manufacturer defined
“ “ - manufacturer defined
“ “ - reserved for future
Taking the example trouble code (0133), the first
digit (0) would then be replaced with P0, and the 0133
reported would become P0133 (which is the code for
an ‘oxygen sensor circuit slow response’). As for
further examples, if the response had been D016, the
code would be interpreted as U1016, while 1131 would
be P1131.
Had there been codes stored by more than one
module, or more than three codes stored in the same
module, the above response would have consisted of
multiple lines. To determine which module is reporting
each trouble would then require turning the headers on
with an ATH1 command.
ELM322DSF
Elm Electronics – Circuits for the Hobbyist
< http://www.elmelectronics.com/ >
10 of 18
Share Link: 