MPC5565MVZ132 데이터 시트보기 (PDF) - Freescale Semiconductor

부품명

상세내역

제조사

MPC5565MVZ132

Microcontroller

Freescale Semiconductor 

Table 2. Absolute Maximum Ratings 1 (continued)

Electrical Characteristics

Spec

Characteristic

Symbol

Min.

Max.

Unit

28 Maximum solder temperature 11

Lead free (Pb-free)

Leaded (SnPb)

TSDR

—

260.0

oC

—

245.0

29 Moisture sensitivity level 12

MSL

—

3

1 Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only,

and functional operation at the maxima is not guaranteed. Stress beyond any of the listed maxima can affect device reliability

or cause permanent damage to the device.

2 1.5 V ± 10% for proper operation. This parameter is specified at a maximum junction temperature of 150 oC.

3 All functional non-supply I/O pins are clamped to VSS and VDDE, or VDDEH.

4 AC signal overshoot and undershoot of up to ± 2.0 V of the input voltages is permitted for an accumulative duration of

60 hours over the complete lifetime of the device (injection current not limited for this duration).

5 Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met. Keep the negative DC

voltage greater than –0.6 V on SINB during the internal power-on reset (POR) state.

6 Internal structures hold the input voltage less than the maximum voltage on all pads powered by VDDEH supplies, if the

maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications.

7 Internal structures hold the input voltage less than the maximum voltage on all pads powered by VDDE supplies, if the maximum

injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications.

8 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.

9 Total injection current for all analog input pins must not exceed 15 mA.

10 Lifetime operation at these specification limits is not guaranteed.

11 Moisture sensitivity profile per IPC/JEDEC J-STD-020D.

12 Moisture sensitivity per JEDEC test method A112.

3.2 Thermal Characteristics

The shaded rows in the following table indicate information specific to a four-layer board.

Table 3. MPC5565 Thermal Characteristics

Spec

MPC5565 Thermal Characteristic

Symbol 324 PBGA Unit

1 Junction to ambient 1, 2, natural convection (one-layer board)

2 Junction to ambient 1, 3, natural convection (four-layer board 2s2p)

RθJA

RθJA

29

°C/W

19

°C/W

3 Junction to ambient (@200 ft./min., one-layer board)

RθJMA

23

°C/W

4 Junction to ambient (@200 ft./min., four-layer board 2s2p)

RθJMA

16

°C/W

5 Junction to board 4 (four-layer board 2s2p)

RθJB

10

°C/W

6 Junction to case 5

RθJC

7

°C/W

7 Junction to package top 6, natural convection

ΨJT

2

°C/W

1 Junction temperature is a function of on-chip power dissipation, package thermal resistance, mounting site (board)

temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal

resistance.

2 Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal.

3 Per JEDEC JESD51-6 with the board horizontal.

4 Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on

the top surface of the board near the package.

5 Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method

(MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature.

6 Thermal characterization parameter indicating the temperature difference between package top and the junction temperature

per JEDEC JESD51-2.

MPC5565 Microcontroller Data Sheet, Rev. 2.0

Freescale Semiconductor

5

Share Link: