NTE918SM 데이터 시트보기 (PDF) - NTE Electronics
부품명
상세내역
제조사
NTE918SM Datasheet PDF : 4 Pages
| |||
Absolute Maximum Ratings:
Power Supply Voltage, VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V
Power Dissipation (Note 1), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Differential Input Current (Note 2), IID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10mA
Input Voltage (Note 3), VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V
Output Short–Circuit Duration, tS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite
Operating Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C
Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65° to +150°C
Lead Temperature (During Soldering, 10sec), TL
NTE918 (Metal Can) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C
NTE918M (Plastic DIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +260°C
NTE918SM (Surface Mount)
Vapor Phase (60sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
Note 1. The maximum junction temperature of these devices is +110°C. For operating at elevated
temperatures, the NTE918 must be derated based on a thermal resistance of +150°C/W,
junctio to ambient, or +45°C/W, junction to case. The thermal resistance of the NTE918M
and the NTE918SM is +100°C/W, junction to ambient.
Note 2. The inputs are shunted with back–to–back diodes for overvoltage protection. Therefore, ex-
cessive current will flow if a differential input voltage in excess of 1V is applied between the
inputs unless some limiting resistance is used.
Note 3. For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply
voltage.
Electrical Characteristics: (±5V ≤ VS ≤ ±20V, 0° ≤ TA ≤ +70°C, Note 4 unless otherwise specified)
Parameter
Symbol
Test Conditions
Min Typ Max Unit
Input Offset Voltage
VIO
– – 15 V
TA = +25°C
– 4 10 V
Input Offset Current
IIO
– – 300 nA
TA = +25°C
– 30 200 nA
Input Bias Current
IIB
– – 750 nA
TA = +25°C
– 150 500 nA
Input Resistance
ri TA = +25°C
0.5 3.0 – MΩ
Supply Current
ICC, IEE TA = +25°C
– 5 10 mA
Large Signal Voltage Gain
AV VS = ±15V, VOUT = ±10V, RL ≥ 2kΩ
20 – – V/mV
VS = ±15V, VOUT = ±10V, RL ≥ 2kΩ, TA = +25°C 25 200 – V/mV
Slew Rate
SR VS = ±15V, AV = 1, TA = +25°C, Note 5
50 70 – V/µs
Small Signal Bandwidth
BW VS = ±15V, TA = +25°C
– 15 – MHz
Output Voltage Swing
VO VS = ±15V, RL = 2kΩ
±12 ±13 – V
Input Voltage Range
VI VS = ±15V
±11.5 – – V
Common–Mode Rejection Ratio CMRR
100 – – dB
Supply Voltage Rejection Ratio PSRR
65 80 – dB
Note 4. Power supplies must be bypassed with 0.1µF disc capacitors.
Note 5. Slew rate is tested with VS = ±15V. These devices are in a unity–gain non–inverting configuration.
VIN is stepped from –7.5V to +7.5V and vice versa. The slew rates between –5V and +5V and
vice versa are tested and guaranteed to exceed 50V/µs.
Share Link: 