74ALVT16241 데이터 시트보기 (PDF) - NXP Semiconductors.
부품명
상세내역
제조사
74ALVT16241 Datasheet PDF : 16 Pages
| |||
Philips Semiconductors
74ALVT16241
16-bit buffer/driver; 3-state
Table 8: Static characteristics …continued
At recommended operating conditions; voltages are referred to GND (ground = 0 V); Tamb = −40 °C to +85 °C.
Symbol Parameter
Conditions
Min
Typ
Max
VOL
ILI
IOFF
IHOLD
IEX
IPU
IPD
IOZ
ICC
LOW-level output voltage
input leakage current
VCC = 3.0 V
IOL = 100 µA
IOL = 16 mA
IOL = 32 mA
IOL = 64 mA
control pins
data pins
power-down output current
bus hold current on data
inputs
external current into output
power-up 3-state output
current
power-down 3-state output
current
3-state output current
supply current
VCC = 3.6 V; VI = VCC or GND
VCC = 0 V or 3.6 V; VI = 5.5 V
VCC = 3.6 V; VI = VCC
VCC = 3.6 V; VI = 0 V
VCC = 0 V; VI or VO = 0 V to 4.5 V
VCC = 3 V; VI = 0.8 V
VCC = 3 V; VI = 2.0 V
VCC = 0 V to 3.6 V; VI = 3.6 V
output HIGH-state; VO = 5.5 V;
VCC = 3.0 V
VCC ≤ 1.2 V; VO = 0.5 V to VCC;
VI = GND or VCC
VCC ≤ 1.2 V; VO = 0.5 V to VCC;
VI = GND or VCC
VCC = 3.6 V; VI = VIL or VIH
output HIGH-state; VO = 3.0 V
output LOW-state; VO = 0.5 V
VCC = 3.6 V; VI = GND or VCC; IO = 0 A
outputs HIGH-state
-
-
-
-
-
-
[2] -
[2] -
-
[3] 75
[3] −75
±500
[3] -
-
-
-
-
-
0.07 0.2
0.25 0.4
0.3
0.5
0.4
0.55
0.1
0.1
0.5
+0.1
0.1
130
−140
-
10
±1
10
1
−5
±100
-
-
-
125
1
±100
1
±100
0.5
5
+0.5 −5
0.07 0.1
outputs LOW-state
-
3.5
7
outputs disabled
[5] -
0.07 0.1
∆ICC
additional supply current VCC = 3 V to 3.6 V; one input at
[6] -
per input pin
VCC − 0.6 V; other inputs at VCC or
GND
0.04 0.4
Unit
V
V
V
V
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA
mA
mA
mA
mA
[1] All typical values are at VCC = 2.5 V and Tamb = 25 °C.
[2] Unused pins at VCC or GND.
[3] This is the bus hold overdrive current required to force the input to the opposite logic state.
[4] This parameter is valid for any VCC between 0 V and 1.2 V with a transition time of up to 10 ms. From VCC = 1.2 V to VCC = 2.5 V ± 0.2 V
a transition time of 100 µs is permitted. This parameter is valid for Tamb = 25 °C only.
[5] ICC is measured with outputs pulled up to VCC or pulled down to ground.
[6] This is the increase in supply current for each input at the specified voltage level other than VCC or GND.
[7] All typical values are at VCC = 3.3 V and Tamb = 25 °C.
[8] This parameter is valid for any VCC between 0 V and 1.2 V with a transition time of up to 10 ms. From VCC = 1.2 V to VCC = 3.3 V ± 0.3 V
a transition time of 100 µs is permitted. This parameter is valid for Tamb = 25 °C only.
9397 750 15164
Product data sheet
Rev. 03 — 4 July 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
8 of 16
Share Link: 