MCP6561T-E/OT 데이터 시트보기 (PDF) - Microchip Technology

부품명

상세내역

제조사

MCP6561T-E/OT

1.8V Low Power Push-Pull Output Comparator

Microchip Technology 

MCP6561/1R/1U/2/4

1.0 ELECTRICAL

CHARACTERISTICS

1.1 Maximum Ratings*

VDD - VSS ....................................................................... 6.5V

All other inputs and outputs............VSS - 0.3V to VDD + 0.3V

Difference Input voltage ......................................|VDD - VSS|

Output Short Circuit Current .................................... ±25 mA

Current at Input Pins .................................................. ±2 mA

Current at Output and Supply Pins .......................... ±50 mA

Storage temperature ................................... -65°C to +150°C

Ambient temp. with power applied .............. -40°C to +125°C

Junction temp............................................................ +150°C

ESD protection on all pins (HBM/MM)..................≥ 4 kV/300V

*Notice: Stresses above those listed under “Maximum Rat-

ings” may cause permanent damage to the device. This is a

stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operational listings of this specification is not implied. Expo-

sure to maximum rating conditions for extended periods may

affect device reliability.

DC CHARACTERISTICS

Electrical Characteristics: Unless otherwise indicated: VDD = +1.8V to +5.5V, VSS = GND, TA = +25°C, VIN+ = VDD/2, VIN- = VSS,

RL = 10 kΩ to VDD/2 (see Figure 1-1).

Parameters

Symbol Min

Typ

Max Units

Conditions

Power Supply

Supply Voltage

VDD

1.8

Quiescent Current per comparator

IQ

60

Power Supply Rejection Ratio

PSRR

63

Input

Input Offset Voltage

Input Offset Drift

Input Offset Current

Input Bias Current

VOS

-10

ΔVOS/ΔT

—

IOS

—

IB

—

—

—

Input Hysteresis Voltage

VHYST

1.0

Input Hysteresis Linear Temp. Co.

TC1

—

Input Hysteresis Quadratic Temp.

TC2

—

Co.

—

100

70

±3

±2

±1

1

60

1500

—

10

0.3

5.5

V

130

µA IOUT = 0

—

dB VCM = VSS

+10

—

—

—

—

5000

5.0

—

—

mV

µV/°C

pA

pA

pA

pA

mV

µV/°C

µV/°C2

VCM = VSS (Note 1)

VCM = VSS

VCM = VSS

TA = +25°C, VIN- = VDD/2

TA = +85°C, VIN- = VDD/2

TA = +125°C, VIN- = VDD/2

VCM = VSS (Notes 1, 2)

Common-Mode Input Voltage

Range

Common-Mode Rejection Ratio

Common Mode Input Impedance

Differential Input Impedance

Push-Pull Output

VCMR

CMRR

ZCM

ZDIFF

VSS−0.2

VSS−0.3

54

50

54

—

—

—

—

66

63

65

1013||4

1013||2

VDD+0.2

VDD+0.3

—

—

—

—

—

V

V

dB

dB

dB

Ω||pF

Ω||pF

VDD = 1.8V

VDD = 5.5V

VCM= -0.3V to VDD+0.3V, VDD = 5.5V

VCM= VDD/2 to VDD+0.3V, VDD = 5.5V

VCM= -0.3V to VDD/2, VDD = 5.5V

High Level Output Voltage

VOH VDD−0.7 —

—

V IOUT = -3 mA/-8 mA with VDD = 1.8V/5.5V

(Note 3)

Low Level Output Voltage

VOL

—

—

0.6

V IOUT = 3 mA/8 mA with VDD = 1.8V/5.5V

(Note 3)

Short Circuit Current

ISC

—

±30

—

mA Note 3

Output Pin Capacitance

COUT

—

8

—

pF

Note 1: The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the

input-referred trip points.

2: VHYST at different temperatures is estimated using VHYST (TA) = VHYST @ +25°C + (TA - 25°C) TC1 + (TA - 25°C)2 TC2.

3: Limit the output current to Absolute Maximum Rating of 50 mA.

© 2009 Microchip Technology Inc.

DS22139B-page 3

Share Link: