MU9C8K64-50TDC View Datasheet(PDF) - Music Semiconductors
Part Name
Description
Manufacturer
MU9C8K64-50TDC Datasheet PDF : 30 Pages
| |||
MU9C Binary Routing Coprocessor (RCP) Family
be LOW. If the /FI input is HIGH, the /FF output will be
HIGH. The state of the /FF line will not change until after
the rising edge of /E during a Write cycle.
/FI (Full Input, Input)
The /FI input receives full information from the next
higher-priority MU9C RCP in a vertically cascaded
system to provide system-level full information. When the
/FI input is LOW the /FF output will be HIGH if there is at
least one location whose Validity bit is set invalid; when
all locations have their Validity bits set valid, the /FF
output goes LOW. When the /FI input is HIGH, the /FF
output will remain HIGH. The /FF output from one device
is connected to the /FI input of the next lower-priority
device to give system-full indication. The /FI pin of the
highest-priority device must be tied LOW.
/MM (Multiple Match, Open Drain Output)
The /MM line indicates that there is a multiple match
within the system. When the /MI input is HIGH, the /MM
line is pulled LOW if there are at least two matches within
the MU9C RCP as a result of the previous Comparison
cycle; when there are less than two matches, the /MM line
floats HIGH. When the /MI input is LOW, the /MM line is
pulled LOW if there are one or more matches within the
MU9C RCP as a result of the previous Comparison cycle;
when there are no matches, the /MM line floats HIGH.
The /MM lines have open-drain outputs, so all /MM lines
within the system are connected together to give
system-level multiple match indication. The state of the
/MM line will not change until after the rising edge of /E
during a Comparison cycle.
/RESET
The /RESET input is used to reset the MU9C RCP to a
known state. When the /RESET line is pulled LOW it
causes the MU9C RCP to enter its reset state. After power
is applied to the MU9C RCP, the /RESET line must be
held LOW for a time equal to or greater than the minimum
RESET pulse width before the device can operate
correctly. This pin is internally pulled up.
TCLK (JTAG Test Clock, Input)
The TCLK input is the Test Clock input. This pin is
internally pulled up.
TMS (JTAG Test Mode Select, Input)
The TMS input is the Test Mode Select input. This pin is
internally pulled up.
TDI (JTAG Test Data Input, Input)
The TDI input is the Test Data input. This pin is internally
pulled up.
TDO (JTAG Test Data Output, Output)
The TCLK output is the Test Data Output. This pin is
internally pulled up.
/TRST (JTAG Reset, Input)
The /TRST input is the Reset input, and serves to reset the
Test Access Port circuitry to its reset condition. This pin is
internally pulled up.
VDD, VSS (Positive Power Supply, Ground)
These pins are the main power supply connections to the
MU9C RCP. VDD must be held at +3.3 Volts and ± 0.3
Volts relative to the VSS pin, which is at 0 Volts, system
reference potential, for correct operation of the device.
Note: The TCLK, TMS, TDI, TDO, and /TRST lines are defined
in the IEEE Standard Test Access Port and Boundary-scan
Architecture IEEE Standard. 1149.1-1990 and IEEE Standard.
1149.1a-1993.
FUNCTIONAL DESCRIPTION
Data is read from and written to the MU9C RCP through
the DQ31–0 lines. The Control bus, which is comprised of
Chip Enable (/E), two Chip Selects (/CS1, /CS2), Write
Enable (/W), Output Enable (/OE), Validity Bit Control
(/VB), Address Valid (/AV), Data Segment Control (DSC),
and the Address/Control inputs (AC bus) controls the
MU9C RCP. When the /AV line is LOW, the AC bus
carries an address for random access into the Memory
array; when it is HIGH, the AC bus conveys control
information. The MU9C RCP control states perform
Register Read/Write, Memory Read/Write, Data Move,
Comparison, Validity Bit Control, Initialization, and
Address Register Control. These functions are
summarized in Control State Overview on page 15.
Random access to memory locations occurs when the /AV
line is LOW; during a Write cycle, the validity of the
location is set by the /VB input. When the /AV line is
HIGH the control states allow read and write access to the
register set comprising Comparand register, seven mask
registers, a Configuration register, a Status register, an
Address register, a Device Select register, and an
Instruction register. The Configuration register sets the
persistent operating conditions of the device: the Page
address of the device, selection of mask register for
directly addressed memory writes, and selection between
hardware and software control.
Rev. 6
5
Share Link: 