M1AGL1000V2-FG144I View Datasheet(PDF) - Microsemi Corporation
Part Name
Description
Manufacturer
M1AGL1000V2-FG144I Datasheet PDF : 250 Pages
| |||
IGLOO DC and Switching Characteristics
Table 2-2 • Recommended Operating Conditions 1
Symbol
Parameter
Commercial Industrial Units
TA
TJ
VCC3
Ambient Temperature
Junction Temperature 2
1.5 V DC core supply voltage5
0 to +70
–40 to +85 °C
0 to +85
–40 to +100 °C
1.425 to 1.575 1.425 to 1.575 V
1.2 V–1.5 V wide range DC
core supply voltage 4,6
1.14 to 1.575 1.14 to 1.575 V
VJTAG JTAG DC voltage
1.4 to 3.6
1.4 to 3.6
V
VPUMP Programming voltage
VCCPLL8 Analog power supply (PLL)
Programming Mode
3.15 to 3.45 3.15 to 3.45 V
Operation 7
0 to 3.6
0 to 3.6
V
1.5 V DC core supply voltage5 1.425 to 1.575 1.425 to 1.575 V
1.2 V – 1.5 V DC core supply 1.14 to 1.575 1.14 to 1.575 V
voltage4,6
VCCI and 1.2 V DC core supply voltage6
VMV 9
1.2 V DC wide range DC
supply voltage6
1.14 to 1.26 1.14 to 1.26 V
1.14 to 1.575 1.14 to 1.575 V
1.5 V DC supply voltage
1.425 to 1.575 1.425 to 1.575 V
1.8 V DC supply voltage
1.7 to 1.9
1.7 to 1.9
V
2.5 V DC supply voltage
3.0 V DC supply voltage 10
2.3 to 2.7
2.7 to 3.6
2.3 to 2.7
V
2.7 to 3.6
V
3.3 V DC supply voltage
3.0 to 3.6
3.0 to 3.6
V
LVDS differential I/O
2.375 to 2.625 2.375 to 2.625 V
LVPECL differential I/O
3.0 to 3.6
3.0 to 3.6
V
Notes:
1. All parameters representing voltages are measured with respect to GND unless otherwise specified.
2. To ensure targeted reliability standards are met across ambient and junction operating temperatures, Microsemi
recommends that the user follow best design practices using Microsemi’s timing and power simulation tools.
3. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
standard are given in Table 2-25 on page 2-24. VCCI should be at the same voltage within a given I/O bank.
4. All IGLOO devices (V5 and V2) must be programmed with the VCC core voltage at 1.5 V. Applications using the V2
devices powered by 1.2 V supply must switch the core supply to 1.5 V for in-system programming.
5. For IGLOO® V5 devices
6. For IGLOO V2 devices only, operating at VCCI VCC.
7. VPUMP can be left floating during operation (not programming mode).
8. VCCPLL pins should be tied to VCC pins. See the "Pin Descriptions" chapter of the IGLOO FPGA Fabric User’s Guide
for further information.
9. VMV pins must be connected to the corresponding VCCI pins. See the "Pin Descriptions" chapter of the IGLOO FPGA
Fabric User’s Guide for further information.
10. 3.3 V wide range is compliant to the JESD-8B specification and supports 3.0 V VCCI operation.
Table 2-3 • Flash Programming Limits – Retention, Storage, and Operating Temperature1
Product
Grade
Commercial
Programming
Cycles
500
Program Retention Maximum Storage Maximum Operating Junction
(biased/unbiased) Temperature TSTG (°C) 2
Temperature TJ (°C) 2
20 years
110
100
Industrial
500
20 years
110
100
Notes:
1. This is a stress rating only; functional operation at any condition other than those indicated is not implied.
2. These limits apply for program/data retention only. Refer to Table 2-1 on page 2-1 and Table 2-2 for device operating
conditions and absolute limits.
2-2
Revision 23
Share Link: 