EM8470 View Datasheet(PDF) - Unspecified

Part Name

Description

Manufacturer

EM8470

MPEG-4 Decoder for Set-top, DVD and Streaming Applications

Unspecified 

EM8470, EM8471, EM8475, EM8476

Alpha Blending

Alpha blending provides two layers of blending: sub-picture

over the MPEG video and OSD over both the sub-picture

and MPEG video. Up to 16 levels of blending are available.

Video Input and Output Interfaces

Video output ports provide digital RGB or YCbCr outputs and

include an integrated NTSC/PAL video encoder and video

DACs for composite, s-video and component analog outputs.

VBI Support

NTSC closed captioning on lines 21 and 284 is supported. In

addition, NTSC widescreen signaling (WSS) and copy gen-

eration management (CGMS-A) on lines 20 and 283, as

defined by IEC 61880, is supported. This information speci-

fies the aspect ratio of the current program and also provides

copy protection capabilities.

PAL widescreen signaling (WSS) on line 23, as defined by

ETSI EN300284 and ITU-R BT.1119, is supported. This infor-

mation specifies the aspect ratio of the current program.

Digital Video Output

The digital video output, controlled by the video display con-

troller, supports 8- / 16-bit CCIR 601 / 656 4:2:2 YCbCr data.

An additional 24-bit RGB output mode is supported on the

EM8475 and EM8476. It may be operated as a timing master

or slave at rates up to 80 MHz (160 MBps) and resolutions

up to 720p or 1080i.

The 24-bit RGB output mode supports HDCP (High-band-

width Digital Content Protection) when interfaced to a DVI

transmitter chip.

TV Encoder - Composite and S-Video Output

A high-quality NTSC/PAL encoder (with optional Macrovision

v7.1 protection) that supports the NTSC-M, NTSC-J, PAL-

B/D/G/H/I, PAL-60 and PAL-M baseband video standards is

available. It features three 10-bit video DACs to generate

simultaneous composite and s-video outputs. The analog

video outputs are capable of driving a doubly-terminated 75-

ohm load.

Component Analog Output

The EM8475 and EM8476 also include component YPbPr or

RGB analog outputs, with optional Macrovision AGC v1.03

protection in 480p YPbPr mode. This component analog out-

put can be programmed to be either RGB or YPbPr video

data, interlaced or progressive, from NTSC / PAL resolution

up to 1920x1080. The analog video outputs are capable of

driving a doubly-terminated 75-ohm load.

When generating analog RGB or YPbPr video, the compos-

ite video output is always present; the s-video output is not

available.

Supported analog formats are:

• RGB and composite video for SCART support

• RGB with sync on green

• SMPTE GBR

• Betacam YUV

• M-II YUV

• SMPTE YPbPr

If copy protection is used during DVD-Video playback, the

resolution on the EM8475 analog YPbPr / RGB outputs may

not be higher than standard definition (720x480 or 720x576)

unless driving a VGA monitor. If the output is configured to

be progressive YPbPr, only 480p video may be generated.

Digital Video Input

The video input port, available only on the EM8475 and

EM8476, is designed to capture video data in 8- / 16-bit

CCIR 601 / 656 YCbCr video data formats. The capture port

must operate in slave mode, synchronized to the input clock

and sync signals. The capture port is designed to support

video rates up to 80 MHz (160 MBps) and resolutions up to

720p or 1080i.

This input may be converted to progressive using either field

merging or scan line interpolation.

Note that only one video stream can be displayed at a time -

either MPEG video or input video.

Sigma Designs, Inc.

355 Fairview Way • Milpitas, CA, USA 95035 • Tel: 408.262.9003 • Fax: 408.957.9740

www.sigmadesigns.com • sales@sigmadesigns.com

-5-

Share Link: