SC18IS600(2006) View Datasheet(PDF) - NXP Semiconductors.
Part Name
Description
Manufacturer
SC18IS600 Datasheet PDF : 28 Pages
| |||
NXP Semiconductors
SC18IS600/601
SPI to I2C-bus interface
8. Static characteristics
Table 11. Static characteristics
VDD = 2.4 V to 3.6 V; Tamb = −40 °C to +85 °C (industrial); unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
IDD(oper)
IDD(idle)
IDD(tpd)
Vth(HL)
Vth(LH)
Vhys
VOL
VOH
operating supply current
Idle mode supply current
total Power-down mode supply
current
HIGH-LOW threshold voltage
LOW-HIGH threshold voltage
hysteresis voltage
LOW-level output voltage
HIGH-level output voltage
VDD = 3.6 V; f = 12 MHz
VDD = 3.6 V; f = 18 MHz
VDD = 3.6 V; f = 12 MHz
VDD = 3.6 V; f = 18 MHz
VDD = 3.6 V; industrial
VDD = 3.6 V; extended
Schmitt trigger input
Schmitt trigger input
all pins; IOL = 20 mA
all pins; IOL = 10 mA
all pins; IOL = 3.2 mA
all pins; IOH = −8 mA;
push-pull mode
-
-
-
-
-
-
0.22VDD
-
-
-
-
-
VDD − 1
7
11
3.6
4
< 0.1
-
0.4VDD
0.6VDD
0.2VDD
0.6
0.3
0.2
-
13
16
4.8
6
5
50
-
0.7VDD
-
1.0
0.5
0.3
-
all pins; IOH = −3.2 mA;
push-pull mode
VDD − 0.7 VDD − 0.4 -
all pins; IOH = −20 µA;
quasi-bidirectional mode
VDD − 0.3 VDD − 0.2 -
Cig
input capacitance at gate
[2] -
-
IIL
LOW-level input current
logical 0; VI = 0.4 V
[3] -
-
ILI
input leakage current
all ports; VI = VIL or VIH
[4] -
-
ITHL
HIGH-LOW transition current
all ports; logical 1-to-0; [5][6] −30
-
VI = 2.0 V at VDD = 3.6 V
RRESET_N(int) internal pull-up resistance on pin
RESET
10
-
15
−80
±10
−450
30
Unit
mA
mA
mA
mA
µA
µA
V
V
V
V
V
V
V
V
V
pF
µA
µA
µA
kΩ
[1] Typical ratings are not guaranteed. The values listed are at room temperature, 3 V.
[2] Pin capacitance is characterized but not tested.
[3] Measured with pins in quasi-bidirectional mode.
[4] Measured with pins in high-impedance mode.
[5] Pins in quasi-bidirectional mode with weak pull-up (applies to all pins with pull-ups).
[6] Pins source a transition current when used in quasi-bidirectional mode and externally driven from logic 1 to logic 0. This current is
highest when VI is approximately 2 V.
SC18IS600_601_3
Product data sheet
Rev. 03 — 13 December 2006
© NXP B.V. 2006. All rights reserved.
17 of 28
Share Link: 