MAX19700EVKIT View Datasheet(PDF) - Maxim Integrated
Part Name
Description
Manufacturer
MAX19700EVKIT Datasheet PDF : 18 Pages
| |||
MAX19700 Evaluation Kit/Evaluation System
DESIGNATION QTY
DESCRIPTION
U1
1
Maxim MAX19700ETM (48-pin thin
QFN 7mm x 7mm)
20-bit dual-supply bus transceiver
(56-pin TSSOP)
U2
1 Texas Instruments
SN74AVCH20T245GR
U3
U4, U5
U6
1 Maxim MAX9113ESA (8-pin SO)
2 Maxim MAX4108ESA (8-pin SO)
1 Maxim MAX4478AUD (14-pin TSSOP)
Component List (continued)
DESIGNATION QTY
DESCRIPTION
U7
1 Maxim MAX3023EUD (14-pin TSSOP)
Maxim MAX3027EUD (14-pin TSSOP)
Dual-supply 5-bit signal translator
U8
1 (14-pin DQFN)
Fairchild FXL5T244
None
None
None
8 Shunts
1 MAX19700 PC board
1 MAX19700 EV kit software (CD-ROM)
Component Suppliers
SUPPLIER
PHONE
FAX
WEBSITE
AVX
843-946-0238
843-626-3123
www.avxcorp.com
Central Semiconductor
631-435-1110
631-435-1824
www.centralsemi.com
Coilcraft
847-639-6400
847-639-1469
www.coilcraft.com
Diodes Inc.
805-446-4800
805-446-4850
www.diodes.com
Fairchild
888-522-5372
—
www.fairchildsemi.com
Panasonic
714-373-7366
714-737-7323
www.panasonic.com
TDK
847-803-6100
847-390-4405
www.component.tdk.com
Texas Instruments
972-644-5580
214-480-7800
www.ti.com
Vishay/Vitramon
203-268-6261
203-452-5670
www.vishay.com
Zetex USA
631-543-7100
631-864-7630
www.zetex.com
Note: Indicate that you are using the MAX19700 when contacting these component suppliers.
Quick Start
Recommended Equipment
• DC power supplies:
Analog (VDD)
+3.0V, 100mA
Clock (CVDD)
+3.0V, 100mA
Digital (OVDD)
+1.8V, 100mA
Buffers (BVCC)
+3.3V, 100mA
Op-Amp Positive (VOP)
+5.0V, 250mA
Op-Amp Negative (VON) -5.0V, 250mA
• Signal generator with low phase noise and low jitter
for clock input signal (e.g., HP 8662A, HP 8644B)
• Two signal generators with low phase noise for ana-
log signal inputs (e.g., HP 8662A, HP 8644B)
• Logic analyzer or data-acquisition system (e.g., HP
16500C, TLA621)
• Analog bandpass filters (e.g., Allen Avionics, K&L
Microwave) for input signals and clock signal
• Two spectrum analyzers (e.g., HP 8560E)
• One 10-bit digital pattern generator (e.g., Tektronix
DG2020A)
Procedure
The MAX19700 EV kit is a fully assembled and tested
surface-mount board. Follow the steps below to verify
board operation. Do not turn on power supplies or
enable signal/data generators until all connections
are completed.
Command Module Setup
1) Set both switches at SW1 to the OFF position to dis-
able the SDA/SCL pullup resistors.
2) Place a shunt across pins 1-2 of the VDD select
jumper (command module working voltage set
to +3.3V).
_______________________________________________________________________________________ 3
Share Link: 