MAX1482CPD View Datasheet(PDF) - Maxim Integrated
Part Name
Description
Manufacturer
MAX1482CPD Datasheet PDF : 14 Pages
| |||
20µA, 1⁄8-Unit-Load, Slew-Rate-Limited
RS-485 Transceivers
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VCC) ...............................................................7V
Control Input Voltages (RE, DE) .................-0.5V to (VCC + 0.5V)
Driver Input Voltage (DI).............................-0.5V to (VCC + 0.5V)
Driver Output Voltages ..........................................-7.5V to 12.5V
Receiver Input Voltages (A, B) ..............................-7.5V to 12.5V
Receiver Output Voltage (RO)....................-0.5V to (VCC + 0.5V)
Continuous Power Dissipation (TA = +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) .....727mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C) .800mW
8-Pin SO (derate 5.88mW/°C above +70°C)..................471mW
14-Pin SO (derate 8.33mW/°C above +70°C)................667mW
8-Pin µMAX (derate 4.10mW/°C above +70°C) .............330mW
Operating Temperature Ranges
MAX148_C_ _ .......................................................0°C to +70°C
MAX148_E_ _.....................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = 5V ±5%, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
Differential Driver Output (no load)
Differential Driver Output
(with load)
Change in Magnitude of Driver
Differential Output Voltage for
Complementary Output States
Driver Common-Mode Output
Voltage
Change in Magnitude of Driver
Common-Mode Output Voltage
for Complementary Output States
VOD1
VOD2
∆VOD
VOC
∆VOD
R = 50Ω (RS-422), Figure 1
R = 27Ω (RS-485), Figure 1
R = 27Ω or 50Ω, Figure 1
R = 27Ω or 50Ω, Figure 1
R = 27Ω or 50Ω, Figure 1
Three-State (high impedance)
Output Current at Driver
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
Input Current
(A, B)
Receiver Differential Threshold
Voltage
Receiver Input Hysteresis
Receiver Output High Voltage
Receiver Output Low Voltage
IOZD
VIH
VIL
IIN1
IIN2
VTH
∆VTH
VOH
VOL
MAX1482 only,
-7V < VY and VZ < 12V
DE, DI, –R—E–
DE, DI, –R—E–
DE, DI, –R—E–
MAX1482,
DE = 0V, VCC = 0V or 5.25V
MAX1483,
DE = 0V, VCC = 0V or 5.25V
-7V ≤ VCM ≤ 12V
VCM = 0V
IO = -4mA, VID = 200mV
IO = 4mA, VID = -200mV
VIN = 12V
VIN = -7V
VIN = 12V
VIN = -7V
Three-State (high impedance)
Output Current at Receiver
IOZR 0.4V ≤ VO ≤ 2.4V
Receiver Input Resistance
RIN
-7V ≤ VCM ≤ 12V
MIN TYP MAX UNITS
5
V
2
5
V
1.5
5
0.2
V
3
V
0.2
V
±50
µA
2.0
V
0.8
V
±2
µA
150
-100
µA
200
-150
-0.2
0.2
V
75
mV
3.5
V
0.4
V
±1
µA
96
kΩ
Note 1: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device
ground unless otherwise specified.
2 _______________________________________________________________________________________
Share Link: 