LS7166-TS24(2002) View Datasheet(PDF) - LSI Corporation
Part Name
Description
Manufacturer
LS7166-TS24 Datasheet PDF : 12 Pages
| |||
I/O DESCRIPTION:
(See REGISTER DESCRIPTION for I/O Prgramming.)
Data-Bus (D0-D7) (Pin 8-Pin 15). The 8-line data bus is a
three-state I/O bus for interfacing with the system bus.
CS (Chip Select Input) (Pin 2). A logical "0" at this input en-
ables the chip for Read and Write.
RD (Read Input) (Pin 19). A logical "0" at this input enables the
OSR and the OL to be read on the data bus.
WR (Write Input) (Pin 1) A logical "0" at this input enables the
data bus to be written into the control and data registers.
C/D (Control/Data Input) (Pin 18). A logical "1" at this input en-
ables a control word to be written into one of the four control
registers or the OSR to be read on the I/O bus. A logical "0" en-
ables a data word to be written into the PR, or the OL to be read
on the I/O bus.
A (Pin 6). Input A is a programmable count input capable of
functioning in three different modes, such as up count input,
down count input and quadrature input.
B (Pin 7). Input B is also a programmable count input that can
be programmed to function either as down count input, or count
direction control gate for input A, or quadrature input. When B is
programmed as count direction control gate, B = 0 enables A as
the Up Count input and B = 1 enables A as the Down Count in-
put. When programmed as the direction input, B can switch
state only when A is high.
ABGT/RCTR (PIN 4). This input can be programmed to func-
tion as either inputs A and B enable gate or as external counter
reset input. A logical "0" is the active level on this input.
In non-quadrature mode, if Pin 4 is programmed as A and B en-
able gate input, it may switch state only when A is high (if A is
clock and B is direction) or when both A and B are high (if A
and B are clocks. In quadrature mode, if Pin 4 is programmed
as A and B enable gate, it may switch state only when either A
or B switches.
LCTR/LLTC (PIN 3). This input can be programmed to func-
tion as the external load command input for either the CNTR or
the OL. When programmed as counter load input, the counter
is loaded with the data contained in the PR. When pro-
grammed as the OL load input, the OL is loaded with data con-
tained in the CNTR. A logical "0" is the active level on this in-
put.
CY (Pin 16). This output can be programmed to serve as one
of the following:
A. CY. Complemented Carry out (active "0").
B. CY. True Carry out (active "1").
C. CYT. Carry Toggle flip-flop out.
D. COMP. Comparator out (active "0")
BW (Pin 17). This output can be programmed to serve as one
of the following:
A. BW. Complemented Borrow out (active "0").
B. BW. True Borrow out (active "1").
C. BWT. Borrow Toggle flip-flop out.
D. COMPT. Comparator Toggle output.
VDD (Pin 5). Supply voltage positive terminal.
VSS (Pin 20). Supply voltage negative terminal.
Absolute Maximum Ratings:
Parameter
Symbol
Voltage at any input
VIN
Operating Temperature
TA
Storage Temperature
Supply Voltage
TSTG
VDD - VSS
Values
VSS - 0.3 to VDD + 0 .3
0 to +70
-65 to +150
+7.0
Unit
Volts
oC
oC
Volts
DC Electrical Characteristics. (All voltages referenced to VSS.
TA = 0˚ to 70˚C, VDD = 4.5V to 5.5V, fc = 0, unless otherwise specified)
Parameter
Supply Voltage
Supply Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Input Current
Symbol
VDD
IDD
VIL
VIH
VOL
VOH
-
Min. Value
4.5
-
0
2.0
-
2.5
-
Max.Value
5.5
350
0.8
VDD
0.4
-
15
Output Source Current
ISRC
200
-
Output Sink Current
ISINK
4
-
Data Bus Off-State
Leakage Current
-
-
15
Unit
Volts
µA
Volts
Volts
Volts
Volts
nA
µA
mA
nA
Remarks
-
Outputs open
-
-
4mA Sink
200µA Source
Leakage
Current
VOH = 2.5V
VOL = 0.4V
-
7166-111299-5
Share Link: 