AD8352 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
AD8352 Datasheet PDF : 19 Pages
| |||
Data Sheet
FEATURES
−3 dB bandwidth of 2.2 GHz (AV = +10 dB)
Single resistor gain adjust: 3 dB ≤ AV ≤ 25 dB
Single resistor and capacitor distortion adjust
Input resistance: 3 kΩ, independent of gain (AV)
Differential or single-ended input to differential output
Low noise input stage: 2.7 nV/√Hz RTI at AV = 10 dB
Low broadband distortion
10 MHz: −86 dBc HD2, −82 dBc HD3
70 MHz: −84 dBc HD2, −82 dBc HD3
190 MHz: −81 dBc HD2, −87 dBc HD3
OIP3 of 41 dBm at 150 MHz
Slew rate: 8 V/ns
Fast settling and overdrive recovery of <2 ns
Single-supply operation: 3 V to 5.5 V
Low power dissipation: 37 mA typical at 5 V
Power-down capability: 5 mA at 5 V
Fabricated using the high speed XFCB3 SiGe process
APPLICATIONS
Differential ADC drivers
Single-ended-to-differential conversion
RF/IF gain blocks
SAW filter interfacing
GENERAL DESCRIPTION
The AD8352 is a high performance differential amplifier
optimized for RF and IF applications. It achieves better than
80 dB SFDR performance at frequencies up to 200 MHz, and
65 dB beyond 500 MHz, making it an ideal driver for high
speed 12-bit to 16-bit analog-to-digital converters (ADCs).
Unlike other wideband differential amplifiers, the AD8352 has
buffers that isolate the gain setting resistor (RG) from the signal
inputs. As a result, the AD8352 maintains a constant 3 kΩ input
resistance for gains of 3 dB to 25 dB, easing matching and input
drive requirements. The AD8352 has a nominal 100 Ω differential
output resistance.
The device is optimized for wideband, low distortion performance
at frequencies beyond 500 MHz. These attributes, together with
its wide gain adjust capability, make this device the amplifier of
choice for general-purpose IF and broadband applications
where low distortion, noise, and power are critical. It is ideally
suited for driving not only ADCs but also mixers, pin diode
attenuators, surface acoustic wave (SAW) filters, and multi-
element discrete devices. The device is available in a compact
2 GHz, Ultralow Distortion,
Differential RF/IF Amplifier
AD8352
FUNCTIONAL BLOCK DIAGRAM
RG CD
ENB
RGP
RDP
VIP
RD
VIN
RDN
RGN
BIAS CELL
VCM
VCC
+
–
Figure 1.
VOP
VON
GND
AD8352
3 mm × 3 mm, 16-lead LFCSP and operates over a temperature
range of −40°C to +85°C.
–60
44
–65
42
–70
40
–75
38
–80
36
–85
34
–90
32
–95
30
–100
28
20 40 60 80 100 120 140 160 180 200 220
FREQUENCY (MHz)
Figure 2. Third Harmonic Distortion (HD3) and IP3 vs.
Frequency, Measured Differentially
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2006–2018 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
Share Link: 