ADP7104 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADP7104 Datasheet PDF : 25 Pages
| |||
ADP7104
Data Sheet
Parameter
THERMAL SHUTDOWN
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
PROGRAMMABLE EN/UVLO
UVLO Threshold Rising
UVLO Threshold Falling
UVLO Hysteresis Current
Enable Pull-Down Current
Start Threshold
Shutdown Threshold
Hysteresis
OUTPUT NOISE
POWER SUPPLY REJECTION RATIO
Symbol
TSSD
TSSD-HYS
UVLORISE
UVLOFALL
UVLOHYS
IEN-IN
VSTART
VSHUTDOWN
OUTNOISE
PSRR
Conditions
Min
TJ rising
3.3 V ≤ VIN ≤ 20 V, TJ = −40°C to +125°C
1.18
3.3 V ≤ VIN ≤ 20 V, TJ = −40°C to +125°C, 10 kΩ in
series with the enable pin
VEN > 1.25 V, TJ = −40°C to +125°C
7.5
EN = VIN
TJ = −40°C to +125°C
TJ = −40°C to +125°C
2.45
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.8 V
10 Hz to 100 kHz, VIN = 6.3 V, VOUT = 3.3 V
10 Hz to 100 kHz, VIN = 8 V, VOUT = 5 V
10 Hz to 100 kHz, VIN = 12 V, VOUT = 9 V
10 Hz to 100 kHz, VIN = 5.5 V, VOUT = 1.5 V,
adjustable mode
10 Hz to 100 kHz, VIN = 12 V, VOUT = 5 V,
adjustable mode
10 Hz to 100 kHz, VIN = 20 V, VOUT = 15 V,
adjustable mode
100 kHz, VIN = 4.3 V, VOUT = 3.3 V
100 kHz, VIN = 6 V, VOUT = 5 V
10 kHz, VIN = 4.3 V, VOUT = 3.3 V
10 kHz, VIN = 6 V, VOUT = 5 V
100 kHz, VIN = 3.3 V, VOUT = 1.8 V, adjustable mode
100 kHz, VIN = 6 V, VOUT = 5 V, adjustable mode
100 kHz, VIN = 16 V, VOUT = 15 V, adjustable mode
10 kHz, VIN = 3.3 V, VOUT = 1.8 V, adjustable mode
10 kHz, VIN = 6 V, VOUT = 5 V, adjustable mode
10 kHz, VIN = 16 V, VOUT = 15 V, adjustable mode
Typ Max
150
15
1.22 1.28
1.13
9.8 12
500
3.2
250
15
15
15
15
18
30
65
50
50
60
60
50
60
60
60
80
80
Unit
C
C
V
V
μA
nA
V
V
mV
μV rms
μV rms
μV rms
μV rms
μV rms
μV rms
μV rms
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
1 Based on an end-point calculation using 1 mA and 300 mA loads. See Figure 6 for typical load regulation performance for loads less than 1 mA.
2 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
voltages above 3.0 V.
3 Start-up time is defined as the time between the rising edge of EN to VOUT being at 90% of its nominal value.
4 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 5.0 V
output voltage is defined as the current that causes the output voltage to drop to 90% of 5.0 V, or 4.5 V.
INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS
Table 2.
Parameter
Minimum Input and Output Capacitance1
4F
Capacitor ESR
Symbol
CMIN
RESR
Conditions
TA = −40°C to +125°C
TA = −40°C to +125°C
Min
Typ Max Unit
0.7
μF
0.001
0.2
Ω
1 The minimum input and output capacitance should be greater than 0.7 μF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;
Y5V and Z5U capacitors are not recommended for use with any LDO.
Rev. I | Page 4 of 25
Share Link: 