ADSP-21469KBZ-ENG2 View Datasheet(PDF) - Analog Devices

Part Name

Description

Manufacturer

ADSP-21469KBZ-ENG2

SHARC Processor

Analog Devices 

ADSP-21469/ADSP-21469W

KEY FEATURES—PROCESSOR CORE

At 450 MHz core instruction rate, the ADSP-21469 performs

at 2.7 GFLOPS/900 MMACs

5 Mbits on-chip, RAM for simultaneous access by the core

processor and DMA

DDR2 DRAM interface (16-bit) operating at maximum fre-

quency of half the core clock frequency

Dual data address generators (DAGs) with modulo and bit-

reverse addressing

Zero-overhead looping with single-cycle loop setup, provid-

ing efficient program sequencing

VISA (variable instruction set) execution support

Single instruction multiple data (SIMD) architecture

provides:

Two computational processing elements

Concurrent execution

Code compatibility with other SHARC family members at

the assembly level

Parallelism in buses and computational units allows:

Single cycle executions (with or without SIMD) of a mul-

tiply operation, an ALU operation, a dual memory read

or write, and an instruction fetch

Transfers between memory and core at a sustained

7.2 Gbytes/second bandwidth

FFT accelerator implements radix-2 complex/real input, com-

plex output FFT with no core intervention

IIR accelerators perform dedicated IIR filtering with high-per-

formance, fixed- and floating-point processing capabilities

with no core intervention

FIR accelerators perform dedicated FIR filtering with high-

performance, fixed- and floating-point processing capabil-

ities with no core intervention

In the ADSP-21469, the program sequencer can execute code

directly from external memory bank 0 (SRAM, as well as

DDR2 DRAM). This allows more options to a user in terms

of code and data storage.

New opcodes of 16 and 32 bits are supported in addition to

the existing 48 bit opcodes. Variable Instruction Set Archi-

tecture (VISA) execution from external DDR2 DRAM

memory is also supported.

INPUT/OUTPUT FEATURES

Two 8-bit wide link ports can connect to the link ports of

other SHARCs or peripherals. Link ports are bidirectional

programmable ports having eight data lines, an acknowl-

edge line and a clock line. Link ports can operate at a

maximum frequency of 166 MHz.

DMA controller supports:

36 DMA channels for transfers between ADSP-21469 inter-

nal memory and a variety of peripherals

DMA transfers at peripheral clock speed, in parallel with

full-speed processor execution

External port provides glueless connection to 16-bit wide

synchronous DDR2 DRAM using a dedicated DDR2 DRAM

controller, and 8-bit wide asynchronous memory devices

using asynchronous memory interface (AMI)

Preliminary Technical Data

Programmable wait state options (for AMI): 2 to 31

DDR2_CLK cycles

Delay-line DMA engine maintains circular buffers in

external memory with tap/offset based reads

16-bit data access for synchronous DDR2 DRAM

8-bit data access for asynchronous memory

4 memory select lines allows multiple external memory

devices

Digital audio interface (DAI) includes eight serial ports, four

precision clock generators, an input data port, an S/PDIF

transceiver, and a signal routing unit

Digital peripheral interface (DPI) includes, two timers, one

UART, and two SPI ports, and a two-wire interface port

Outputs of PCG’s A and B can be routed through DAI pins

Outputs of PCG's C and D can be driven on to DAI as well as

DPI pins

Eight dual data line serial ports— each has a clock, frame

sync, and two data lines that can be configured as either a

receiver or transmitter pair

TDM support for telecommunications interfaces including

128 TDM channel support for newer telephony interfaces

such as H.100/H.110

Up to 16 TDM stream support, each with 128 channels per

frame

Companding selection on a per channel basis in TDM mode

Input data port (IDP), configurable as eight channels of serial

data or seven channels of serial data and up to a 20-bit

wide parallel data channel

Signal routing unit provides configurable and flexible con-

nections between the various peripherals and the DAI/DPI

components

4 independent asynchronous sample rate converters (ASRC).

Each converter has separate serial input and output ports,

a de-emphasis filter providing up to –128 dB SNR perfor-

mance, stereo sample rate converter and supports left-

justified, I2S, TDM, and right-justified modes and 24-, 20-,

18-, and 16-audio data word lengths.

2 muxed flag/IRQ lines

1 muxed flag/IRQ /AMI_MS pin

1 muxed flag/Timer expired line /AMI_MS pin

S/PDIF-compatible digital audio receiver/transmitter sup-

ports EIAJ CP-340 (CP-1201), IEC-958, AES/EBU standards

Left-justified, I2S or right-justified serial data input with

16-, 18-, 20- or 24-bit word widths (transmitter)

Pulse-width modulation provides:

16 PWM outputs configured as four groups of four outputs

supports center-aligned or edge-aligned PWM waveforms

PLL has a wide variety of software and hardware multi-

plier/divider ratios

Thermal diode to monitor die temperature

Available in 19 mm by 19 mm PBGA package (see Ordering

Guide on Page 56)

Rev. PrB | Page 2 of 56 | November 2008

Share Link: