TDA2616Q View Datasheet(PDF) - Philips Electronics
Part Name
Description
Manufacturer
TDA2616Q Datasheet PDF : 12 Pages
| |||
Philips Semiconductors
2 x 12 W hi-fi audio power amplifiers with
mute
Product specification
TDA2616/TDA2616Q
SYMBOL
PARAMETER
CONDITIONS
MIN. TYP. MAX. UNIT
∆VGND DC output offset voltage
−
40
200 mV
Operating position; note 6
IP
total quiescent current
PO
output power
THD
B
total harmonic distortion
power bandwidth
THD = 0.5%
THD = 10%
THD = 0.5%; RL = 4 Ω
THD = 10%; RL = 4 Ω
PO = 4 W
THD = 0.5%; note 2
18 40
70 mA
5
6
−
W
6.5 8
−
W
−
10
−
W
−
14
−
W
−
0.13
0.2 %
−
40 to
−
Hz
20 000
Gv
Gv
Vno
Zi
SVRR
α
voltage gain
gain unbalance
noise output voltage
input impedance
supply voltage ripple rejection
channel separation
note 3
29 30
−
0.2
−
70
14 20
35 44
−
45
31 dB
1
dB
140 µV
26
kΩ
−
dB
−
dB
MUTE POSITION (IMUTE ≥ 300 µA)
VO
output voltage
Z2-7
mute input impedance
IP
total quiescent current
Vno
noise output voltage
SVRR supply voltage ripple rejection
∆Voff
offset voltage with respect to operating
position
VI = 600 mV
note 7
note 3
note 4
−
0.3
6.7 9
18 40
−
70
35 44
−
4
1.0 mV
11.3 kΩ
70 mA
140 µV
−
dB
150 mV
I2
current if pin 2 is connected to pin 5
−
−
8.2 mA
Notes to the characteristics
1. VP = ±16 V; RL = 8 Ω; Tamb = 25 °C; f = 1 kHz; symmetrical power supply IMUTE < 30 µA. See Fig.4
2. The power bandwidth is measured at an output power of PO max − 3 dB
3. The noise output voltage (RMS value) is measured at RS = 2 kΩ, unweighted (20 Hz to 20 kHz)
4. The ripple rejection is measured at RS = 0 and f = 100 Hz to 20 kHz. The ripple voltage (200 mV) is applied in phase
to the positive and the negative supply rails. With asymmetrical power supplies, the ripple rejection is measured at
f = 1 kHz
5. ±VP = 4 V; RL = 8 Ω; Tamb = 25 °C; f = 1 kHz; symmetrical power supply. See Fig.4
6. VP = 24 V; RL = 8 Ω; Tamb = 25 °C; f = 1 kHz; asymmetrical power supply IMUTE < 30 µA. See Fig.5
7. The internal network at pin 2 is a resistor devider of typical 4 kΩ and 5 kΩ to the positive supply rail. At the connection
of the 4 kΩ and 5 kΩ resistor a zener diode of typical 6.6 V is also connected to the positive supply rail. The spread
of the zener voltage is 6.1 to 7.1 V.
July 1994
7
Share Link: 