AT89C55WD-33JU View Datasheet(PDF) - Atmel Corporation

Part Name

Description

Manufacturer

AT89C55WD-33JU

8-bit Microcontroller with 20K Bytes Flash

Atmel Corporation 

AT89C55WD

Note that not all of the addresses are occupied, and unoccupied addresses may not be imple-

mented on the chip. Read accesses to these addresses will in general return random data, and

write accesses will have an indeterminate effect.

User software should not write 1s to these unlisted locations, since they may be used in future

products to invoke new features. In that case, the reset or inactive values of the new bits will

always be 0.

Timer 2 Registers: Control and status bits are contained in registers T2CON (shown in Table 5-

2) and T2MOD (shown in Table 5-2) for Timer 2. The register pair (RCAP2H, RCAP2L) are the

Capture/Reload registers for Timer 2 in 16-bit capture mode or 16-bit auto-reload mode.

Interrupt Registers: The individual interrupt enable bits are in the IE register. Two priorities can

be set for each of the six interrupt sources in the IP register.

Dual Data Pointer Registers: To facilitate accessing both internal and external data memory,

two banks of 16-bit Data Pointer Registers are provided: DP0 at SFR address locations 82H-

83H and DP1 at 84H-85H. Bit DPS = 0 in SFR AUXR1 selects DP0 and DPS = 1 selects DP1.

The user should always initialize the DPS bit to the appropriate value before accessing the

respective Data Pointer Register.

Power Off Flag: The Power Off Flag (POF) is located at bit 4 (PCON.4) in the PCON SFR. POF

is set to “1” during power up. It can be set and reset under software control and is not affected by

reset.

Table 5-2. T2CON—Timer/Counter 2 Control Register

T2CON Address = 0C8H

Bit Addressable

TF2

EXF2

RCLK

TCLK

Bit

7

6

5

4

EXEN2

3

Reset Value = 0000 0000B

TR2

C/T2

CP/RL2

2

1

0

Symbol

TF2

EXF2

RCLK

TCLK

EXEN2

TR2

C/T2

CP/RL2

Function

Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2 will not be set when either RCLK

= 1 or TCLK = 1.

Timer 2 external flag set when either a capture or reload is caused by a negative transition on T2EX and EXEN2 = 1.

When Timer 2 interrupt is enabled, EXF2 = 1 will cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be

cleared by software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).

Receive clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its receive clock in serial port

Modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the receive clock.

Transmit clock enable. When set, causes the serial port to use Timer 2 overflow pulses for its transmit clock in serial port

Modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for the transmit clock.

Timer 2 external enable. When set, allows a capture or reload to occur as a result of a negative transition on T2EX if

Timer 2 is not being used to clock the serial port. EXEN2 = 0 causes Timer 2 to ignore events at T2EX.

Start/Stop control for Timer 2. TR2 = 1 starts the timer.

Timer or counter select for Timer 2. C/T2 = 0 for timer function. C/T2 = 1 for external event counter (falling edge

triggered).

Capture/Reload select. CP/RL2 = 1 causes captures to occur on negative transitions at T2EX if EXEN2 = 1. CP/RL2 = 0

causes automatic reloads to occur when Timer 2 overflows or negative transitions occur at T2EX when EXEN2 = 1.

When either RCLK or TCLK = 1, this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.

7

1921D–MICRO–6/08

Share Link: