MCM6205DJ15 View Datasheet(PDF) - Motorola => Freescale
Part Name
Description
Manufacturer
MCM6205DJ15 Datasheet PDF : 8 Pages
| |||
TRUTH TABLE (X = Don’t Care)
E1 E2 G W
Mode
H X X X Not Selected
X L X X Not Selected
L H H H Output Disabled
LHLH
Read
LHX L
Write
VCC Current
ISB1, ISB2
ISB1, ISB2
ICCA
ICCA
ICCA
Output
High–Z
High–Z
High–Z
Dout
High–Z
Cycle
—
—
—
Read Cycle
Write Cycle
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
– 0.5 to + 7.0
V
Voltage Relative to VSS For Any Pin
Except VCC
Vin, Vout – 0.5 to VCC + 0.5 V
Output Current
Iout
± 20
mA
Power Dissipation
PD
1.0
W
Temperature Under Bias
Tbias
– 10 to + 85
°C
Operating Temperature
TA
0 to + 70
°C
Storage Temperature — Plastic
Tstg
– 55 to + 125
°C
NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are
exceeded. Functional operation should be restricted to RECOMMENDED OPER-
ATING CONDITIONS. Exposure to higher than recommended voltages for
extended periods of time could affect device reliability.
This device contains circuitry to protect the
inputs against damage due to high static volt-
ages or electric fields; however, it is advised
that normal precautions be taken to avoid
application of any voltage higher than maxi-
mum rated voltages to this high–impedance
circuit.
This CMOS memory circuit has been de-
signed to meet the dc and ac specifications
shown in the tables, after thermal equilibrium
has been established. The circuit is in a test
socket or mounted on a printed circuit board
and transverse air flow of at least 500 linear
feet per minute is maintained.
DC OPERATING CONDITIONS AND CHARACTERISTICS
(VCC = 5.0 V ± 10%, TA = 0 to 70°C, Unless Otherwise Noted)
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min
Typ
Supply Voltage (Operating Voltage Range)
Input High Voltage
VCC
4.5
5.0
VIH
2.2
—
Input Low Voltage
VIL
– 0.5*
—
* VIL (min) = – 0.5 V dc; VIL (min) = – 2.0 V ac (pulse width ≤ 20 ns)
** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2.0 V ac (pulse width ≤ 20 ns)
DC CHARACTERISTICS
Parameter
Input Leakage Current (All Inputs, Vin = 0 to VCC)
Output Leakage Current (E1 = VIH or G = VIH or E2 = VIL, Vout = 0 to VCC)
Output High Voltage (IOH = – 4.0 mA)
Output Low Voltage (IOL = 8.0 mA)
Symbol
Min
Ilkg(I)
—
Ilkg(O)
—
VOH
2.4
VOL
—
POWER SUPPLY CURRENTS
Parameter
Symbol
– 15
– 20
AC Active Supply Current (Iout = 0 mA, VCC = Max, f = fmax)
ICCA
140
135
AC Standby Current (E1 = VIH, or E2 = VIL, VCC = Max, f = fmax)
ISB1
40
40
CMOS Standby Current (VCC = Max, f = 0 MHz, E1 ≥ VCC – 0.2 V or
ISB2
20
20
E2 ≤ VSS + 0.2 V, Vin ≤ VSS + 0.2 V, or ≥ VCC – 0.2 V)
Max
Unit
5.5
V
VCC + 0.3** V
0.8
V
Max
Unit
±1
µA
±1
µA
—
V
0.4
V
– 25
Unit
130
mA
35
mA
20
mA
MCM6205D
2
MOTOROLA FAST SRAM
Share Link: 