DatasheetQ Logo
Electronic component search and free download site. Transistors,MosFET ,Diode,Integrated circuits

CYRF7936(2008) View Datasheet(PDF) - Cypress Semiconductor

Part Name
Description
Manufacturer
CYRF7936
(Rev.:2008)
Cypress
Cypress Semiconductor Cypress
CYRF7936 Datasheet PDF : 21 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
CYRF7936
Table 1. Pin Description - CYRF7936 40-Pin QFN (continued)
Pin Number
Name
33
VIO
19
RESV
2, 4, 5, 9, 14, 15, NC
18, 17, 20, 21, 22,
23, 32, 36, 39, 31
12
GND
E-PAD
GND
Corner Tabs
NC
Type
Pwr
I
NC
Default
Description
IO interface voltage, 1.8–3.6V.
Must be connected to GND.
Connect to GND.
GND
GND
NC
Ground.
Must be soldered to Ground.
Do Not solder the tabs and keep other signal traces clear. All tabs are
common to the lead frame or paddle which is grounded after the pad is
grounded. While they are visible to the user, they do not extend to the bottom.
Functional Overview
The CYRF7936 IC is designed to implement wireless device
links operating in the worldwide 2.4 GHz ISM frequency band.
It is intended for systems compliant with worldwide regulations
covered by ETSI EN 301 489-1 V1.41, ETSI EN 300 328-1
V1.3.1 (Europe), FCC CFR 47 Part 15 (USA and Industry
Canada), and TELEC ARIB_T66_March, 2003 (Japan).
The CYRF7936 contains a 2.4 GHz CyFi radio modem which
features a 1 Mbps GFSK radio front-end, packet data buffering,
packet framer, DSSS baseband controller, and Received
Signal Strength Indication (RSSI). CYRF7936 features a SPI
interface for data transfer and device configuration.
The CyFi radio modem supports 98 discrete 1 MHz channels
(regulations may limit the use of some of these channels in
certain jurisdictions).
The baseband performs DSSS spreading/despreading, Start
of Packet (SOP), End of Packet (EOP) detection, and CRC16
generation and checking. The baseband may also be
configured to automatically transmit Acknowledge (ACK)
handshake packets whenever a valid packet is received.
When in receive mode, with packet framing enabled, the
device is always ready to receive data transmitted at any of the
supported bit rates. This enables the implementation of
mixed-rate systems in which different devices use different
data rates. This also enables the implementation of dynamic
data rate systems that use high data rates at shorter distances
or in a low-moderate interference environment or both. It
changes to lower data rates at longer distances or in high inter-
ference environments or both.
In addition, the CYRF7936 IC has a Power Management Unit
(PMU), which allows direct connection of the device to any
battery voltage in the range 1.8V to 3.6V. The PMU conditions
the battery voltage to provide the supply voltages required by
the device, and may supply external devices.
Data Transmission Modes
The CyFi radio transceiver supports two different data trans-
mission modes:
In GFSK mode, data is transmitted at 1 Mbps, without any
DSSS.
In 8DR mode, DSSS is enabled and eight bits are encoded
in each derived code symbol transmitted.
Both 64 chip and 32 chip Pseudo Noise (PN) codes are
supported in 8DR mode. In general, lower data rates reduce
packet error rate in any given environment.
Packet Framing
The CYRF7936 IC device supports the following data packet
framing features:
SOP
Packets begin with a two-symbol Start-of-Packet (SoP)
marker. The SOP_CODE_ADR PN code used for the SOP is
different from that used for the “body” of the packet, and if
desired may be a different length. SOP must be configured to
be the same length on both sides of the link.
Length
This is the first eight bits after the SOP symbol, and is trans-
mitted at the payload data rate. An EoP condition is inferred
after reception of the number of bytes defined in the length
field, plus two bytes for the CRC16.
CRC16
The device may be configured to append a 16 bit CRC16 to
each packet. The CRC16 uses the USB CRC polynomial with
the added programmability of the seed. If enabled, the receiver
verifies the calculated CRC16 for the payload data against the
received value in the CRC16 field. The seed value for the
CRC16 calculation is configurable, and the CRC16 transmitted
may be calculated using either the loaded seed value or a zero
seed; the received data CRC16 is checked against both the
configured and zero CRC16 seeds.
Document #: 001-48013 Rev. **
Page 3 of 21
[+] Feedback

Share Link: 

datasheetq.com  [ Privacy Policy ]Request Datasheet ] [ Contact Us ]