EL4342ILZA-EVAL View Datasheet(PDF) - Intersil
Part Name
Description
Manufacturer
EL4342ILZA-EVAL Datasheet PDF : 13 Pages
| |||
EL4340, EL4342
Absolute Maximum Ratings (TA = +25°C)
Supply Voltage (V+ to V-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . V- -0.5V, V+ +0.5V
Supply Turn-on Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Digital & Analog Input Current (Note 6) . . . . . . . . . . . . . . . . . . 50mA
Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7). . . .2500V
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W)θJC (°C/W)
32 Ld QFN Package (Notes 4, 5). . . . .
35
1.3 to 8
24 Ld QSOP Package (Note 4) . . . . . .
88
N/A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . .-40°C to +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact
product reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
6. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications V+ = +5V, V- = -5V, GND = 0V, TA = +25°C, Input Video = 1VP-P and RL = 500Ω to GND, CL = 5pF unless
otherwise specified.
PARAMETER
DESCRIPTION
CONDITIONS
MIN TYP MAX UNIT
GENERAL
+IS Enabled
Enabled Supply Current (EL4340)
Enabled Supply Current (EL4342)
No load, VIN = 0V, Enable Low
26
30
34
mA
39
46
50
mA
-IS Enabled
Enabled Supply Current (EL4340)
Enabled Supply Current (EL4342)
No load, VIN = 0V, Enable Low
-32
-30
-24
mA
-48
-46 -36.5 mA
+IS Disabled
-IS Disabled
VOUT
IOUT
VOS
VOS
Ib
ROUT
ROUT
RIN
ACL or AV
ITRI
LOGIC
Disabled Supply Current (EL4340)
Disabled Supply Current (EL4342)
Disabled Supply Current
Positive and Negative Output Swing
Output Current
Output Offset Voltage (EL4340)
Output Offset Voltage (EL4342)
Input Bias Current
HIZ Output Resistance
Enabled Output Resistance
Input Resistance
Voltage Gain
Output Current in Three-state
No load, VIN = 0V, Enable High
No load, VIN = 0V, Enable High
No load, VIN = 0V, Enable High
VIN = ±3.5V, RL = 500Ω
RL = 10Ω to GND
VIN = 0V
HIZ = Logic High
HIZ = Logic Low
VIN = ±3.5V
VIN = ±1.5V, RL= 500Ω
VOUT = 0V
2.3
2.8
3.3
mA
3
3.5
4
mA
10
100
µA
±3.1 ±3.4
V
±80 ±135
mA
-15
7
+15
mV
-10
+10
mV
-1
-2
-3
µA
1.4
MΩ
0.2
Ω
10
MΩ
0.98 0.99 1.02 V/V
8
15
22
µA
VIH
Input High Voltage (Logic Inputs)
VIL
Input Low Voltage (Logic Inputs)
IIH
Input High Current (Logic Inputs)
IIL
Input Low Current (Logic Inputs)
VH = 5V
VL = 0V
2
V
0.8
V
215
270
320
µA
2
3
µA
3
FN7421.3
October 18, 2010
Share Link: 