ISP1102 View Datasheet(PDF) - Philips Electronics
Part Name
Description
Manufacturer
ISP1102 Datasheet PDF : 23 Pages
| |||
Philips Semiconductors
ISP1102
Advanced USB transceiver
Table 11: Static characteristics: supply pins…continued
VCC(5.0) = 4.0 to 5.5 V or Vreg(3.3) = 3.0 to 3.6 V; VCC(I/O) = 1.65 to 3.6 V; VGND = 0 V; see Table 8 for valid voltage level
combinations; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Unit
ICC(susp)
suspend supply current
SUSPND = HIGH
ICC(I/O)(sharing) sharing mode I/O supply current VCC(5.0) not connected
IDx(sharing)
sharing mode load current on
pins D+ and D−
VCC(5.0) not connected;
SOFTCON = LOW;
VDx = 3.6 V
VCC(5.0)th
supply voltage detection
threshold
1.65 V ≤ VCC(I/O) ≤ 3.6 V
supply lost
[4] -
-
20
µA
-
-
20
µA
-
-
10
µA
-
-
3.6
V
supply present
4.1
-
-
V
VCC(5.0)hys
supply voltage detection
hysteresis
VCC(I/O) = 1.8 V
-
70
-
mV
VCC(I/O)th
I/O supply voltage detection
threshold
Vreg(3.3) = 2.7 to 3.6 V
supply lost
-
-
0.5
V
supply present
1.4
-
-
V
VCC(I/O)hys
I/O supply voltage detection
hysteresis
Vreg(3.3) = 3.3 V
-
0.45 -
V
Vreg(3.3)th
regulated supply voltage
detection threshold
1.65 V ≤ VCC(I/O) ≤ Vreg(3.3);
2.7 V ≤ Vreg(3.3) ≤ 3.6 V
supply lost
-
-
0.8
V
supply present
[5] 2.4
-
-
V
Vreg(3.3)hys
regulated supply voltage
detection hysteresis
VCC(I/O) = 1.8 V
-
0.45 -
V
[1] Iload includes the pull-up resistor current via pin Vpu(3.3).
[2] The minimum voltage is 2.7 V in the suspend mode.
[3] Maximum value characterized only, not tested in production.
[4] Excluding any load current and Vpu(3.3) or Vsw source current to the 1.5 kΩ and 15 kΩ pull-up and pull-down resistors (200 µA typ.).
[5] When VCC(I/O) < 2.7 V, the minimum value for Vreg(3.3)th = 2.0 V for supply present condition.
Table 12: Static characteristics: digital pins
VCC(I/O) = 1.65 to 3.6 V; VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
VCC(I/O) = 1.65 to 3.6 V
Input levels
VIL
LOW-level input voltage
-
-
VIH
HIGH-level input voltage
0.6VCC(I/O)
-
Output levels
VOL
LOW-level output voltage
IOL = 100 µA
-
-
VOH
HIGH-level output voltage
Leakage current
IOL = 2 mA
IOH = 100 µA
IOH = 2 mA
-
-
VCC(I/O) − 0.15 -
VCC(I/O) − 0.4 -
ILI
input leakage current
[1] −1
-
Max
Unit
0.3VCC(I/O)
V
-
V
0.15
V
0.4
V
-
V
-
V
+1
µA
9397 750 11228
Product data
Rev. 03 — 02 September 2003
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
10 of 23
Share Link: 