LC6513A(2001) View Datasheet(PDF) - SANYO -> Panasonic

Part Name

Description

Manufacturer

LC6513A
(Rev.:2001)

Single-Chip 4-Bit Microcomputer for Control-Oriented Applications (Low-Threshold Input, On-Chip FLT Driver)

SANYO -> Panasonic 

Ordering number:EN2367B

CMOS IC

LC6512A, LC6513A

Single-Chip 4-Bit Microcomputer

for Control-Oriented Applications

(Low-Threshold Input, On-Chip FLT Driver)

General Description

The LC6512A, 6513A are microcomputers that are dentical

with FLT driver-contained microcomputers LC6502D,

6505D in instruction set but are further enhanced in perfor-

mance, such as shorter cycle time, more stack levels, in-

creased FLT drive capacity, and are partially changed in

specifications for standby function. Since the LC6512A,

6513A are also pin-compatible with the LC6502D, 6505D,

they can be used as similar replacements for the LC6502D,

6505D. The LC6512A, 6513A can replace the LC6502B/

6502D, 6505B/6505D to enhance performances of equip-

ment in which these microcomputers have been applied so

far.

(3) The standby function is the same as for the LC6514B

and its using method is different from that of the

LC6502D, 6505D, etc.

Package Dimensions

unit:mm

3025B-D42SIC

[LC6512A]

42

22

Features

• Low power dissipation CMOS single-chip microcomputer.

• Instruction set with 79 instructions common to the

LC6502C, 6502B, 6502D/LC6505C, 6505B, 6505D.

• 2-source, 2-level interrupt function (external interrupt/

internal timer interrupt)

• 8-level stack

• 4-bit prescaler-contained 8-bit programmable timer

• FLT driver-contained output ports and low-threshold in-

put ports

(1) Digits driving output ports: 10 pins

(2) Segments driving output ports: 8 pins

(3) Normal voltage input ports: 8 pins (4 pins: Low-

threshold input port)

(4) Normal voltage input/output ports: 8-pins

• ROM, RAM

(1) LC6512A ROM: 2048bytes, RAM: 128 × 4bits

(2) LC6513A ROM: 1024 bytes, RAM: 64 × 4bits

• Cycle time 1.33µs min.

400kHz, 800kHz, 1MHz, 3MHz ceramic resonator OSC.

• Power-down by 2 standby modes

(1) HALT mode: Power dissipation saving by program

standby during normal operation

(2) HOLD mode: Power supply backup during power

failure

1

21

37.9

0.95

0.48 1.78

1.15

unit:mm

3052A-QIP48A

1.5

36

[LC6513A]

20.0

14.0

1.0

0.35

3.0

1.5

25

SANYO : DIP42S

0.15

37

24

48

1

13

12

2.15

16.6

1.7 SANYO : QIP48A

Any and all SANYO products described or contained herein do not have specifications that can handle

applications that require extremely high levels of reliability, such as life-support systems, aircraft’s

control systems, or other applications whose failure can be reasonably expected to result in serious

physical and/or material damage. Consult with your SANYO representative nearest you before using

any SANYO products described or contained herein in such applications.

SANYO assumes no responsibility for equipment failures that result from using products at values that

exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other

parameters) listed in products specifications of any and all SANYO products described or contained

herein.

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

O1001TN (KT)/7129YT/7227KI/5317KI/N256KI,TS No.2367–1/24

Share Link: