LPC2212 View Datasheet(PDF) - NXP Semiconductors.

Part Name

Description

Manufacturer

LPC2212

16/32-bit ARM microcontrollers; 128/256 kB ISP/IAP flash with 10-bit ADC and external memory interface

NXP Semiconductors. 

NXP Semiconductors

LPC2212/2214

16/32-bit ARM microcontrollers

I 16 kB on-chip static RAM and 128/256 kB on-chip flash program memory. 128-bit wide

interface/accelerator enables high speed 60 MHz operation.

I In-System Programming (ISP) and In-Application Programming (IAP) via on-chip

bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or

full chip erase takes 400 ms.

I EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the

on-chip RealMonitor software as well as high speed real-time tracing of instruction

execution.

I Eight-channel 10-bit ADC with conversion time as low as 2.44 µs.

I Two 32-bit timers (with four capture and four compare channels), PWM unit (six

outputs), Real-Time Clock and Watchdog.

I Multiple serial interfaces including two UARTs (16C550), Fast I2C-bus (400 kbit/s) and

two SPIs.

I Vectored Interrupt Controller with configurable priorities and vector addresses.

I Configurable external memory interface with up to four banks, each up to 16 MB and

8/16/32-bit data width.

I Up to 112 general purpose I/O pins (5 V tolerant). Up to nine edge or level sensitive

external interrupt pins available.

I 60 MHz maximum CPU clock available from programmable on-chip Phase-Locked

Loop with settling time of 100 µs.

I On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.

I Two low power modes, Idle and Power-down.

I Processor wake-up from Power-down mode via external interrupt.

I Individual enable/disable of peripheral functions for power optimization.

I Dual power supply:

N CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).

N I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.

3. Ordering information

Table 1. Ordering information

Type number

Package

Name

Description

Version

LPC2212FBD144

LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2212FBD144/00 LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2212FBD144/01 LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2214FBD144

LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2214FBD144/00 LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2214FBD144/01 LQFP144 plastic low profile quad flat package; 144 leads; SOT486-1

body 20 × 20 × 1.4 mm

LPC2212_2214_4

Product data sheet

Rev. 04 — 3 January 2008

© NXP B.V. 2008. All rights reserved.

2 of 45

Share Link: