LPC1776(2011) View Datasheet(PDF) - NXP Semiconductors.
Part Name
Description
Manufacturer
LPC1776
(Rev.:2011)
(Rev.:2011)
NXP Semiconductors.
LPC1776 Datasheet PDF : 117 Pages
| |||
NXP Semiconductors
LPC178x/7x
32-bit ARM Cortex-M3 microcontroller
Table 3. Pin description …continued
Not all functions are available on all parts. See Table 2 (Ethernet, USB, LCD, QEI, SD/MMC, DAC pins) and Table 7 (EMC
pins).
Symbol
Description
P0[11]
P0[12]
P0[13]
P0[14]
P0[15]
P0[16]
P0[17]
100 R14 P12 70 [3] I; I/O
PU I
I/O
O
-
-
-
O
41 R1 J4 29 [5] I; I/O
PU O
I/O
I
45 R2 J5 32 [5] I; I/O
PU O
I/O
I
69 T7
M5 48 [3] I; I/O
PU O
I/O
O
128 J16 H13 89 [3] I; I/O
PU O
I/O
130 J14 H14 90 [3] I; I/O
PU I
I/O
126 K17 J12 87 [3] I; I/O
PU I
I/O
P0[11] — General purpose digital input/output pin.
U2_RXD — Receiver input for UART2.
I2C2_SCL — I2C2 clock input/output (this pin does not use a
specialized I2C pad).
T3_MAT1 — Match output for Timer 3, channel 1.
R — Function reserved.
R — Function reserved.
R — Function reserved.
LCD_VD[10] — LCD data.
P0[12] — General purpose digital input/output pin.
USB_PPWR2 — Port Power enable signal for USB port 2.
SSP1_MISO — Master In Slave Out for SSP1.
ADC0_IN[6] — A/D converter 0, input 6. When configured as an
ADC input, the digital function of the pin must be disabled.
P0[13] — General purpose digital input/output pin.
USB_UP_LED2 — USB port 2 GoodLink LED indicator. It is
LOW when device is configured (non-control endpoints
enabled). It is HIGH when the device is not configured or during
global suspend.
SSP1_MOSI — Master Out Slave In for SSP1.
ADC0_IN[7] — A/D converter 0, input 7. When configured as an
ADC input, the digital function of the pin must be disabled.
P0[14] — General purpose digital input/output pin.
USB_HSTEN2 — Host Enabled status for USB port 2.
SSP1_SSEL — Slave Select for SSP1.
USB_CONNECT2 — SoftConnect control for USB port 2.
Signal used to switch an external 1.5 k resistor under software
control. Used with the SoftConnect USB feature.
P0[15] — General purpose digital input/output pin.
U1_TXD — Transmitter output for UART1.
SSP0_SCK — Serial clock for SSP0.
P0 [16] — General purpose digital input/output pin.
U1_RXD — Receiver input for UART1.
SSP0_SSEL — Slave Select for SSP0.
P0[17] — General purpose digital input/output pin.
U1_CTS — Clear to Send input for UART1.
SSP0_MISO — Master In Slave Out for SSP0.
LPC178X_7X
Objective data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 27 May 2011
© NXP B.V. 2011. All rights reserved.
13 of 117
Share Link: