LXM1612-12-03 View Datasheet(PDF) - Microsemi Corporation
Part Name
Description
Manufacturer
LXM1612-12-03 Datasheet PDF : 6 Pages
| |||
A MICROSEMI COMPANY
LXM1612-12-xx
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
PRELIMINARY DATASHEET
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Parameter
Input Supply Voltage Range (Fully Regulated
Lamp Current)
Input Supply Voltage Range (Functional)
Output Power
Brightness Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness)
Operating Ambient Temperature Range
Symbol
VIN1
PO
VBRT_ADJ
VLAMP
IOLAMP
TA
Recommended Operating Conditions
Min
R.C.
Max
10.8
12
13.2
9.6
12
14.4
3.5
4.0
0.0
2.5
5
450
535
620
5.8
0
70
Units
V
W
V
VRMS
mARMS
°C
Unless otherwise specified, the following specifications apply over the recommended operating conditions and ambient temperature of
25°C except where otherwise noted.
Parameter
Symbol
Test Conditions
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current
Min. Average Lamp Current
(Note 2)
Lamp Start Voltage
Operating Frequency
IL(MAX)
IL(MIN)
VLS
fO
VBRT_ADJ=2.5VDC, SLEEP=HIGH,
Burst Duty=100%, VIN1=12VDC
VBRT_ADJ=0VDC, SLEEP=HIGH, Burst Duty=2.0%,
VIN1=12VDC
0°C <TA < 70°C, VIN1 > 9.6VDC
VBRT_ADJ=2.5VDC, SLEEP=HIGH, VIN1=9.6V – 14.4V
BRITE INPUT
Input Current
IBRT
VBRT_ADJ=0VDC
VBRT_ADJ=2.5VDC
Input Voltage for Max. Lamp Current VBRT_ADJ IO(LAMP)=100% Duty Cycle
Input Voltage for Min. Lamp Current VBRT_ADJ IO(LAMP)= Minimum Duty Cycle
SLEEP INPUT
RUN Mode
SLEEP Mode
V SLEEP(HI)
V SLEEP(LO)
VIN1=12V
VIN1=12V
Input Current
I SLEEP
SLEEP=5.0V
SLEEP=0V
VSYNC CHARACTERISTICS
Logic High Level
VSYNCH(HI) VIN1=12V
VSYNCH(LO) VIN1=12V
Input Impedance
ZIN
Input Frequency
POWER CHARACTERISTICS
fSYNC
Sleep Current
IIN(MIN) VIN1=12VDC, SLEEP=0.0V
Note 2: Minimum lamp current required to maintain even light output may vary with display panel.
Average RMS current = (burst duty cycle) x (burst amplitude of 5.8mARMS)
LXM1612-12-xx
Min Typ Max
5.2
1500
63
5.8
0.12
1650
68
6.4
1800
73
-685
-260
2.30
0.0
-728
-282
2.35
-775
-305
2.40
1.9
2.1
VIN1
-5.0
1.9
2.0
390 410 435
0.0
0.0
0.0
1.50 2.5
5.0
-3.0
0.0
1.2
25
27
29
20
200
0.0
0.5
10
Units
mARMS
mARMS
VRMS
kHz
µADC
µADC
VDC
VDC
VDC
VDC
µADC
µADC
VDC
VDC
KΩ
Hz
µADC
Copyright © 2000
Rev. 0.3f, 2000-12-06
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
Share Link: 