MC33298 View Datasheet(PDF) - Freescale Semiconductor
Part Name
Description
Manufacturer
MC33298 Datasheet PDF : 28 Pages
| |||
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 5. Static Electrical Characteristics
Characteristics noted under conditions 4.5V ≤ VDD ≤ 5.5V, 9.0V ≤ VPWR ≤ 16V, -40°C ≤ TA ≤ 125°C, unless otherwise noted.
Typical values noted reflect the approximate value with VBAT = 13V, TA = 25°C.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER INPUT
Supply Voltage Range
Quasi-Functional(16)
Fully Operational
Supply Current (All Outputs ON, IOUT = 0.5A)(17)
Sleep State Supply Current (VDD = 0.5V)
Sleep State Output Leakage Current (per Output, VDD = 0.5V)
Over-voltage Shutdown
Over-voltage Shutdown Hysteresis
Logic Supply Voltage
Logic Supply Current (with any combination of Outputs ON)
Logic Supply Under-voltage Lockout Threshold(18)
POWER OUTPUT
Drain-to-Source ON Resistance (IOUT = 0.5A, TJ = 25°C)
VPWR = 5.5V
VPWR = 9.0V
VPWR = 13V
Drain-to-Source ON Resistance (IOUT = 0.5A, TJ = 150°C)
VPWR = 5.5V
VPWR = 9.0V
VPWR = 13V
VPWR(QF)
5.5
VPWR(FO)
9.0
VPWR(ON)
—
IPWR(SS)
—
IOUT(SS)
—
VOV
28
VOV(HYS)
0.2
VDD
4.5
IDD
—
VDD(UVLO)
2.0
RDS(ON)
—
—
—
RDS(ON)
—
—
—
V
—
9.0
—
26.5
1.0
2.0
V
1.0
50
µA
—
50
µA
—
36
V
—
1.5
V
—
5.5
V
—
4.0
mA
—
4.5
V
Ω
—
1.0
0.4
0.5
0.35
0.45
Ω
—
1.8
7.5
0.9
0.65
0.8
Output Self-limiting Current
Outputs Programmed ON, VOUT = 0.6VDD
IOUT(LIM)
A
3.0
4.0
6.0
Output Fault Detect Threshold(19)
Output Programmed OFF
VOUTTH(F)
VDD
0.6
0.7
0.8
Output OFF Open Load Detect Current(20)
Output Programmed OFF, VOUT = 0.6VDD
IOCO
µA
30
50
100
Output Clamp Voltage
2.0mA < IOUT < 200mA
VOK
V
50
60
75
Output Leakage Current (VDD < 2.0V)(21)
IOUT(LKG)
-50
0
50
µA
Notes
16. SPI inputs and outputs operational; Fault status reporting may not be fully operational within this voltage range.
17. Value reflects normal operation (no faults) with all outputs ON. Each ON output contributes approximately 20µA to IPWR. Each output
experiencing a soft short condition contributes approximately 0.5mA to IPWR. A soft short is defined as any load current causing the
output source current to self-limit. A hard output short is a very low-impedance short to supply.
18. For VDD less than the Under-voltage Lockout Threshold voltage, all data registers are reset and all outputs are disabled.
19. Output Fault Detect Threshold with outputs programmed OFF. Output fault detect thresholds are the same for output opens and shorts.
20. Output OFF Open Load Detect Current is the current required to flow through the load for the purpose of detecting the existence of an
open load condition when the specific output is commanded to be OFF.
21. Output leakage current measured with the output OFF and at 16V.
Analog Integrated Circuit Device Data
Freescale Semiconductor
33298
7
Share Link: 