33991 View Datasheet(PDF) - Motorola => Freescale

Part Name

Description

Manufacturer

33991

Gauge Driver Integrated Circuit

Motorola => Freescale 

Freescale Semiconductor, Inc.

PC33991 SPI INTERFACE AND PROTOCOL DESCRIPTION

INTRODUCTION

The SPI interface has full duplex, three wire synchronous,

16-bit serial synchronous interface data transfer and four I/O

lines associated with it: (SI, SO, SCLK, and CS). The SI/SO

pins of the 33991 follows a first in/first out (D15/D0) protocol

with both input and output words transferring the most

significant bit first. All inputs are compatible with 5.0 V CMOS

logic levels.

DETAILED SIGNAL DESCRIPTIONS

Chip Select (CS)

The Chip Select (CS) pin enables communication with the

Master device. When this pin is in a logic [0] state, the GDIC is

capable of transferring information to, and receiving information

from, the Master. The 33991latches data in from the input shift

registers to the addressed registers on the rising edge of CS.

The output driver on the SO pin is enabled when CS is logic [0].

When CS is logic high, signals at the SCLK and SI pins are

ignored; the SO pin is tri-stated (high impedance). CS will only

be transitioned from a logic [1] state to a logic [0] state when

SCLK is a logic [0]. CS has an internal pull-up (lup) connected

to the pin as specified in the Control I/O table.

Serial Clock (SCLK)

SCLK clocks the internal shift registers of the 33991device.

The serial input (SI) pin accepts data into the Input Shift register

on the falling edge of the SCLK signal while the serial output pin

(SO) shifts data information out of the SO Line Driver on the

rising edge of the SCLK signal. It is important the SCLK pin be

in a logic [0] state whenever the CS makes any transition. SCLK

has an internal pull down (Idwn), specified in the Control I/O

table. When CS is logic [1], signals at the SCLK and SI pins are

ignored; SO is tri-stated (high impedance). See the Data

Transfer Timing diagrams in s 2 and 3.

Serial Input (SI)

This pin is the input of the Serial Peripheral Interface (SPI).

Serial Input (SI) information is read on the falling edge of SCLK.

A 16-bit stream of serial data is required on the SI pin, starting

with the most significant bit (MSB). Messages not multiples of

16 bits (e.g. daisy chained device messages) are ignored. After

transmitting a 16-bit word, the CS pin has to be deasserted

(logic [1]) before transmitting a new word. SI information is

ignored when CS is in a logic high state.

Serial Output (SO)

The Serial Output (SO) data pin is a tri-stateable output from

the shift register. The status register bits are the first 16-bits

shifted out. Those bits are followed by the message bits clocked

in FIFO, when the device is in a daisy chain connection, or

being sent words multiples of 16 bits. Data is shifted on the

rising edge of the SCLK signal. The SO pin remains in a high

impedance state until the CS pin is put into a logic low state.

SYSTEM APPLICATION INFORMATION

This section provides a description of the 33991device SPI

behavior. To follow the explanations below, please refer to the

timing diagrams illustrated in Figures 4 and 5.

Pin

CS (1-to-0)

CS (0-to-1)

SO

SI

Table 1. Data Transfer Timing

SO pin is enabled

Description

33991configuration and desired output states are transferred and executed according to the data in the

shift registers

Will change state on the rising edge of the SCLK pin signal

Will accept data on the falling edge of the SCLK pin signal

33991

12

For More Information OMnOTTOhRiOsLAPrAoNdALuOcGt,INTEGRATED CIRCUIT DEVICE DATA

Go to: www.freescale.com

Share Link: