56F8356 View Datasheet(PDF) - Freescale Semiconductor

Part Name

Description

Manufacturer

56F8356

16-bit Digital Signal Controllers

Freescale Semiconductor 

Document Revision History

Version History

Rev 1.0

Rev 2.0

Rev 3.0

Rev 4.0

Rev 5.0

Rev 6.0

Rev 7.0

Rev 8.0

Rev 9.0

Rev 10.0

Rev 11.0

Rev 12.0

Rev. 13

Description of Change

Initial Public Release

Added Package Pins to GPIO Table in Part 8 General Purpose Input/Output (GPIO). Added

“Typical Min” values to Table 10-18. Editing grammar, spelling, consistency of language

throughout family. Updated values in Regulator Parameters Table 10-9, External Clock

Operation Timing Requirements Table 10-13, SPI Timing Table 10-18, ADC Parameters

Table 10-24, and IO Loading Coefficients at 10MHz Table 10-25.

Added Part 4.8, added the word “access” to FM Error Interrupt in Table 4-5, documenting only

Typ. numbers for LVI in Table 10-6, updated EMI numbers and writeup in Part 10.8.

Updated numbers in Table 10-7 and Table 10-8 with more recent data, Corrected typo in

Table 10-3 in Pd characteristics.

Replace any reference to Flash Interface Unit with Flash Memory Module; corrected thermal

numbers for 144 LQFP in Table 10-3; removed unneccessary notes in Table 10-12; corrected

temperature range in Table 10-14; added ADC calibration information to Table 10-24 and new

graphs in Figure 10-22

Adding/clarifing notes to Table 4-4 to help clarify independent program flash blocks and other

Program Flash modes, clarification to Table 10-23, corrected Digital Input Current Low (pull-up

enabled) numbers in Table 10-5. Removed text and Table 10-2; replaced with note to

Table 10-1.

Added 56F8156 information; edited to indicate differences in 56F8356 and 56F8156. Refor-

matted for Freescale look and feel. Updated Temperature Sensor and ADC tables, then

updated balance of electrical tables for consistency throughout family. Clarified I/O power

description in Table 2-2, added note to Table 10-7 and clarified Section 12.3.

Added output voltage maximum value and note to clarify in Table 10-1; also removed overall

life expectancy note, since life expectancy is dependent on customer usage and must be

determined by reliability engineering. Clarified value and unit measure for Maximum allowed

PD in Table 10-3. Corrected note about average value for Flash Data Retention in Table 10-4.

Added new RoHS-compliant orderable part numbers in Table 13-1.

Updated Table 10-24 to reflect new value for maximum Uncalibrated Gain Error

Deleted RSTO from Pin Group 2 (listed after Table 10-1). Deleted formula for Max Ambient

Operating Temperature (Automotive) and Max Ambient Operating Temperature (Industrial) in

Table 10-4. Added RoHS-compliance and “pb-free” language to back cover.

Added information/corrected state during reset in Table 2-2. Clarified external reference crys-

tal frequency for PLL in Table 10-14 by increasing maximum value to 8.4MHz..

Replaced “Tri-stated” with an explanation in State During Reset column in Table 2-2.

• Added the following note to the description of the TMS signal in Table 2-2:

Note: Always tie the TMS pin to VDD through a 2.2K resistor.

• Added the following note to the description of the TRST signal in Table 2-2:

Note: For normal operation, connect TRST directly to VSS. If the design is to be used in a debugging

environment, TRST may be tied to VSS through a 1K resistor.

Please see http://www.freescale.com for the most current data sheet revision.

56F8356 Technical Data, Rev. 13

2

Freescale Semiconductor

Preliminary

Share Link: