P87LPC778 View Datasheet(PDF) - Philips Electronics
Part Name
Description
Manufacturer
P87LPC778
Philips Electronics
P87LPC778 Datasheet PDF : 79 Pages
| |||
Philips Semiconductors
P87LPC778
CMOS single-chip 8-bit microcontroller
Table 2: Pin description…continued
Symbol
Pin
Type Description
P0.7
13
I/O T1 — Timer/counter 1 external count input or overflow output.
P1.0 - P1.7 12-8, 4, 3, I/O
2
Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for three
pins as noted below. Port 1 latches are configured in the quasi-bidirectional mode and
have either ones or zeros written to them during reset, as determined by the PRHI bit in
the UCFG1 configuration byte. The operation of the configurable port 1 pins as inputs
and outputs depends upon the port configuration selected. Each of the configurable
port pins are programmed independently. Refer to Section 8.9 “I/O ports” and Table 67
“DC electrical characteristics” for details.
Port 1 also provides various special functions as described below:
P1.0
12
O
TxD — Transmitter output for the serial port.
P1.1
11
I
RxD — Receiver input for the serial port.
P1.2
10
I/O T0 — Timer/counter 0 external count input or overflow output.
I/O
SCL — I2C-bus serial clock input/output. When configured as an output, P1.2 is open
drain, in order to conform to I2C-bus specifications.
P1.3
9
I
INT0 — External interrupt 0 input.
I/O
SDA — I2C-bus serial data input/output. When configured as an output, P1.3 is open
drain, in order to conform to I2C-bus specifications.
P1.4
8
I
INT1 — External interrupt 1 input.
P1.5
4
I
RST — External Reset input (if selected via EPROM configuration). A LOW on this pin
resets the microcontroller, causing I/O ports and peripherals to take on their default
states, and the processor begins execution at address 0. When used as a port pin, P1.5
is a Schmitt trigger input only.
P1.6
3
O
P1.6 — Port 1 bit 6.
O
PWM1 — PWM output 1.
P1.7
2
O
P1.7 — Port 1 bit 7.
O
PWM2 — PWM output 2.
P2.0 - P2.1 7, 6
I/O Port 2: Port 2 is a 2-bit I/O port with a user-configurable output type. Port 2 latches are
configured in the quasi-bidirectional mode and have either ones or zeros written to them
during reset, as determined by the PRHI bit in the UCFG1 configuration byte. The
operation of port 2 pins as inputs and outputs depends upon the port configuration
selected. Each port pin is configured independently. Refer to Section 8.9 “I/O ports” and
Table 67 “DC electrical characteristics” for details.
Port 2 also provides various special functions as described below:
P2.0
7
O
X2 — Output from the oscillator amplifier (when a crystal oscillator option is selected via
the EPROM configuration.
O
CLKOUT — CPU clock divided by 6 clock output when enabled via SFR bit and in
conjunction with internal RC oscillator or external clock input.
P2.1
6
I
X1 — Input to the oscillator circuit and internal clock generator circuits (when selected
via the EPROM configuration).
VSS
5
I
Ground: 0 V reference.
VDD
15
I
Power Supply: This is the power supply voltage for normal operation as well as Idle
and Power-down modes.
9397 750 12378
Product data
Rev. 01 — 31 March 2004
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6 of 79
Share Link: