PIC18F65J94 View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC18F65J94

8-Bit LCD Flash Microcontroller with USB and XLP Technology

Microchip Technology 

PIC18F97J94 FAMILY

8-Bit LCD Flash Microcontroller with USB and XLP Technology

Extreme Low-Power Features:

• Multiple Power Management Options for Extreme

Power Reduction:

- VBAT allows for lowest power consumption on

back-up battery (with or without RTCC)

- Deep Sleep allows near total power-down with the

ability to wake-up on external triggers

- Sleep and Idle modes selectively shut down

peripherals and/or core for substantial power

reduction and fast wake-up

• Alternate Clock modes Allow On-the-Fly Switching to

a Lower Clock Speed for Selective Power Reduction

• Extreme Low-Power Current Consumption for

Deep Sleep:

- WDT: 650 nA @ 2V typical

- RTCC: 650 nA @ 32 kHz, 2V typical

- Deep Sleep current, 80 nA typical

Universal Serial Bus Features:

• USB V2.0 Compliant

• Low Speed (1.5 Mb/s) and Full Speed (12 Mb/s)

• Supports Control, Interrupt, Isochronous and Bulk

Transfers

• Supports up to 32 Endpoints (16 bidirectional)

• USB module can use Any RAM Location on the

Device as USB Endpoint Buffers

• On-Chip USB Transceiver

Peripheral Features:

• LCD Display Controller:

- Up to 60 segments by 8 commons

- Internal charge pump and low-power, internal

resistor biasing

- Operation in Sleep mode

• Up to Four External Interrupt Sources

• Peripheral Pin Select Lite (PPS-Lite):

- Allows independent I/O mapping of many

peripherals

• Four 16-Bit Timers/Counters with Prescaler:

- Can be paired as 32-bit timers/counters

• Seven Capture/Compare/PWM (CCP) modules

• Three Enhanced Capture/Compare/PWM (ECCP)

modules:

- One, two or four PWM outputs

- Selectable polarity

- Programmable dead time

- Auto-shutdown and auto-restart

- Pulse steering control

Peripheral Features (continued):

• Hardware Real-Time Clock/Calendar (RTCC):

- Runs in Deep Sleep and VBAT modes

• Two Master Synchronous Serial Ports (MSSP)

modules Featuring:

- 3-Wire/4-Wire SPI (all 4 modes)

- SPI Direct Memory Access (DMA) channel

w/1024 byte count

- Two I2C™ modules Support Multi-Master/Slave

mode and 7-Bit/10-Bit Addressing

• Four Enhanced Addressable USART modules:

- Support RS-485, RS-232 and LIN/J2602

- On-chip hardware encoder/decoder for IrDA®

- Auto-wake-up on Auto-Baud Detect

• Digital Signal Modulator Provides On-Chip OOK,

FSK and PSK Modulation for a Digital Signal Stream

• High-Current Sink/Source 18 mA/18 mA on all Digital I/O

• Configurable Open-Drain Outputs on ECCP/CCP/

USART/MSSP

• Extended Microcontroller mode Using 12, 16 or

20-Bit Addressing mode

Analog Features:

• 10/12-Bit, 24-Channel Analog-to-Digital (A/D)

Converter:

- Conversion rate of 500 ksps (10-bit),

200 kbps (12-bit)

- Conversion available during Sleep and Idle

• Three Rail-to-Rail Enhanced Analog Comparators

with Programmable Input/Output Configuration

• On-Chip Programmable Voltage Reference

• Charge Time Measurement Unit (CTMU):

- Used for capacitive touch sensing, up to

24 channels

- Time measurement down to 1 ns resolution

- CTMU temperature sensing

 2012 Microchip Technology Inc.

DS30575A-page 1

Share Link: