SI3063 View Datasheet(PDF) - Unspecified
Part Name
Description
Manufacturer
SI3063 Datasheet PDF : 62 Pages
| |||
Si306x
Table 4. AC Characteristics
(VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F/K-Grade, see "3. Typical Application Schematic" on page 9)
Parameter
Sample Rate
Symbol
Fs
Test Condition
Min Typ Max Unit
7.2
—
161 kHz
Transmit Frequency Response
Low –3 dBFS Corner
—
0
—
Hz
Receive Frequency Response
Low –3 dBFS Corner,
FILT = 0
—
5
—
Hz
Receive Frequency Response
Low –3 dBFS Corner,
FILT = 1
—
200
—
Hz
Transmit Full Scale Level2
VFS
FULL = 0 (0 dBM)
—
1.1
— VPEAK
Receive Full Scale Level2,3
VFS
FULL = 0 (0 dBM)
1.1
VPEAK
Dynamic Range4,5
DR ILIM = 0, DCV = 11, DCR = 0, —
80
—
dB
IL = 120 mA, MINI = 00
Dynamic Range4,5
DR ILIM = 0, DCV = 00, DCR = 0, —
80
—
dB
IL = 20 mA, MINI = 11
Dynamic Range4,5
DR ILIM = 1, DCV = 11, DCR = 0, —
80
—
dB
IL = 60 mA, MINI = 00
Transmit Total Harmonic Distortion6 THD ILIM = 0, DCV = 11, DCR = 0, —
–72
—
dB
IL = 100 mA, MINI = 00
Transmit Total Harmonic Distortion6 THD ILIM = 0, DCV = 00, DCR = 0, —
–78
—
dB
IL = 20 mA, MINI = 11
Receive Total Harmonic Distortion6 THD ILIM = 0, DCV = 00, DCR = 0, —
–78
—
dB
IL = 20 mA, MINI = 11
Receive Total Harmonic Distortion6 THD ILIM = 1, DCV = 11, DCR = 0, —
–78
—
dB
IL = 50 mA, MINI = 00
Dynamic Range (caller ID mode)7 DRCID
VIN = 1 kHz, –13 dBFS
—
50
—
dB
Caller ID Full Scale Level8
VCID
—
1.6
— VPEAK
AOUT Low Level Current
—
—
10 mA
AOUT High Level Current
—
—
10 mA
Notes:
1. The 32.768 MHz system-side module supports sample rates up to 16 kHz. The 32.4 MHz system-side module supports
sample rates up to a maximum of 10.286 MHz.
2. Measured at TIP and RING with 600 Ω termination at 1 kHz, as shown in Figure 1.
3. Receive full scale level produces –0.9 dBFS at SDO.
4. DR = 20 x log (RMS VFS/RMS VIN) + 20 x log (RMS VIN/RMS noise). VFS is the 0 dBm full-scale level. RMS noise
measurement excludes harmonics. VFS is the 0 dBm full-scale level.
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths. Vin = 1 kHz, –3 dBFS, Fs = 10300 Hz.
6. THD = 20 x log (RMS distortion/RMS signal). Vin = 1 kHz, –3 dBFS, Fs = 10300 Hz.
7. DRCID = 20 x log (RMS VCID/RMS VIN) + 20 x log (RMS VIN/RMS noise). VCID is the 1.5 V full-scale level for the typical
application circuit in Figure 2.
8. With the enhanced CID circuit (refer to "4. Bill of Materials" on page 10), VCID = 1.5 VPEAK and DRCID = 62 dB.
Preliminary Rev. 0.9
7
Share Link: 