CA3274 View Datasheet(PDF) - Intersil
Part Name
Description
Manufacturer
CA3274 Datasheet PDF : 5 Pages
| |||
Specifications CA3274
Absolute Maximum Ratings
Thermal Information
Operating Drive Supply, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . 16V
Maximum Output Current, IO . . . . . . . . . . . . . . . . . . . . . . . . . 200mA
Control, Sense Input. . . . . . . . . . . . . . . . . . . Gnd - 0.5V, VCC + 0.5V
Signal, Power Differential Ground Voltage. . . . . . . . . . . . . . . . . . . ±1V
Thermal Resistance
θJA
Plastic DIP Package 8 Lead . . . . . . . . . . . . . . . . . . . . . 130oC/W
Power Dissipation, PD
Up to 70oC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630mW
Above 70oC . . . . . . . . . . . . . . . . . . . . Derate linearly at 7.7mW/oC
Operating Temperature Range . . . . . . . . . . . . . . . . . -40oC to +85oC
Storage Temperature Range. . . . . . . . . . . . . . . . . . -55oC to +150oC
Lead Temperature (During Soldering)
At distance 1/16in. (1.59mm ± 0.79mm) from
case for 10s Max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +265oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications At TA = -40oC to +85oC, Unless Otherwise Specified
PARAMETERS
SYMBOL
TEST CONDITIONS
MIN
TYP MAX UNITS
Power Supply Current: S1 = 2
ICCH
Control = High (Output On)
-
-
25
mA
ICCL
Control = Low (Output Off)
-
-
5
mA
Control Input: S1 = 3
VTHDH
Thd. Voltage, High
-
-
3.5
V
VTHDL
Thd. Voltage, Low
0.9
-
-
V
VTHDH-VTHDL Hysteresis
0.4
0.65
2.0
V
IIL
Leakage, 0.0 to 5.5V
-20
-
+20
µA
Driver In, Out (Pin 6, 5): S1 = 3
VSAT
Output Saturation Voltage, ICC1 = 200mA,
-
VCONTROL = High
-
0.5
V
ILEAK
Collector Output Leakage, VCONTROL =
-
-
100
µA
Low
Flag Output Low: S1 = 2
Flag Output High: S1 = 3
Prop. Delay: S1 = 1
Sense Input Thd. Level: S1 = 1
Power Supply Rejection Ratio
VFSAT
VFLEAK
tON, tOFF
tFLAG
tD
VSENTHD
PSSR
VSENSE = High, IFLAG = 3mA
Output Leakage, VCC = VFLAG = 10V
Control In to Drive Out
Drive Off to Flag Off
Flag Delay from Control In
-
-
0.8
V
-
-
10
µA
-
5
-
µs
-
10
-
µs
150
-
600
µs
310
335
360
mV
50
-
-
dB
NOTES:
1. Refer to Figure 3 Test Diagram for electrical test connections.
2. Refer to Figure 2 Timing Diagram for logic switching and prop delay.
3. Unless otherwise specified: VCC = VCC1 = VCC2 = 7V to 10V;
VSENSE = “Low”; VCONTROL = “Low”;
Control in levels are defined as “Low” equals 0.0V and “High” equals 5.0V.
10-42
Share Link: 