ADM5170 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADM5170 Datasheet PDF : 6 Pages
| |||
ADM5170
PIN CONFIGURATIONS
DIP
NC 1
28 HO
AO 2
27 HI
AI 3
26 GI
BI 4
25 GO
BO 5
24 FO
CO 6
23 FI
CI
7
ADM5170
TOP VIEW
22 EI
DI 8 (Not to Scale) 21 EO
DO 9
20 VDD
EN 10
19 MS+
VSS 11
SRA 12
18 GND
17 MS–
NC 13
16 NC
NC 14
15 NC
NC = NO CONNECT
PLCC
4 3 2 1 28 27 26
BO 5
CO 6
CI 7
DI 8
DO 9
EN 10
VSS 11
ADM5170
TOP VIEW
(Not to Scale)
25 GO
24 FO
23 FI
22 EI
21 EO
20 VDD
19 MS+
12 13 14 15 16 17 18
NC = NO CONNECT
PIN FUNCTION DESCRIPTION
Mnemonic Function
VDD
VSS
GND
AI . . . HI
AO . . . HO
EN
MS+, MS–
SRA
Power Supply Input, +10 V ± 10%.
Power Supply Input, –10 V ± 10%.
Ground Pin. Must be connected to 0 V.
Digital Input to Drivers A to H.
RS-232/RS-423 Output from Drivers A to H.
Enable Pin. When high, all outputs are 3-stated.
Mode Select Inputs. Used to control the output
level swing. With MS+ & MS– connected to GND,
RS-423A output levels are selected. With MS+
connected to VDD and MS– connected to VSS,
RS-232 output levels are developed.
Slew Rate Adjust Input. An external resistor (2 kΩ
to 10 kΩ) connected between this pin and GND is
used to control the Output Slew Rate (10 V/µs to
2.2 V/µs).
Slew Rate Programming
The slew rate for the ADM5170 is controlled by a single resistor
connected between the SRA pin and GND. The slew rate is
approximately.
Slew Rate (V/µs) = 20/RSRA (kΩ)
Resistors between 2 kΩ and 10 kΩ may be used providing a slew
rate which may be varied from 10 V/µs to 2.2 V/µs. Figure 5 in the
Typical Performance Characteristics section shows how the slew
rate varies with RSRA while Figure 8 shows how the transition time
(10% to 90%) varies with RSRA. Waveshaping of the output allows
the user to control the level of interference (near-end crosstalk)
which may be coupled to adjacent circuits in an interconnection.
The recommended output characteristics for cable length and data
rate are given in the EIA RS-423A specifications.
Maximum Data Rate (kB/s) = 300/t (for rates from 1 kB/s to
100 kB/s).
Cable Length (feet) = 100 X t (Max Length = 4000 ft.)
where t is the transition time (in µs) for the output to swing from
10% to 90% of its steady state values. The absolute maximum data
rate is 100 kB/s and the maximum cable length is limited to 4000 ft.
Output Mode Programming
The ADM5170 has two programmable output modes which
provide different output voltage levels. The low output mode meets
the specifications of EIA standards RS-423A while the high output
mode meets the RS-232 specifications. The high output mode
provides greater output swings and is suitable for driving lines
where higher attenuation levels must be tolerated. This mode is
selected by connecting the mode select pins to the supplies, MS+ to
VDD and MS– to VSS. The low output mode is selected by connect-
ing both mode select pins MS+ and MS– to GND. This mode
provides a controlled output swing with lower output levels.
Inputs
Outputs
MS+ MS–
EN
Data Output
GND GND 0
0
5 V to 6 V (RS-423)
GND GND 0
1
–5 V to –6 V (RS-423)
VDD
VSS
0
0
(VDD – 3 V) (RS-232)1
VDD
VSS
0
1
(VSS + 3 V) (RS-232)1
X
X
1
X
High Z
1Minimum Output Level.
Typical Application Circuit
A typical application circuit using a single driver in the ADM5170
is shown in Figure 4. This circuit is suitable for either RS-232 or
RS-423 communication. An ADM5180 octal receiver is used to
translate the signal back to CMOS logic level at the receiving end.
VH
VDD
VL
INPUT
1/8
ADM5170
EN
RSL
VSS
+V
–V
RS-232/RS-422A
TRANSMISSION
VH
VL
1/8
ADM5180
TIE TO GND
FOR RS-232
Figure 4. RS-232/RS-423A Typical Application Circuit
–4–
REV. 0
Share Link: 