LM75ADP View Datasheet(PDF) - Philips Electronics

Part Name

Description

Manufacturer

LM75ADP

Digital temperature sensor and thermal Watchdog™

Philips Electronics 

Philips Semiconductors

Digital temperature sensor and thermal Watchdog™

Product data sheet

LM75A

GENERAL DESCRIPTION

The LM75A is a temperature-to-digital converter using an on-chip

band-gap temperature sensor and Sigma-delta A-to-D conversion

technique. The device is also a thermal detector providing an

over-temp detection output. The LM75A contains a number of data

registers: Configuration register (Conf) to store the device settings

such as device operation mode, OS operation mode, OS polarity

and OS fault queue as described in the functional description

section; temperature register (Temp) to store the digital temp

reading, and set-point registers (Tos & Thyst) to store programmable

overtemp shutdown and hysteresis limits, that can be communicated

by a controller via the 2-wire serial I2C-bus interface. The device

also includes an open-drain output (OS) which becomes active

when the temperature exceeds the programmed limits. There are

three selectable logic address pins so that eight devices can be

connected on the same bus without address conflict.

The LM75A can be configured for different operation conditions. It

can be set in normal mode to periodically monitor the ambient

temperature, or in shutdown mode to minimize power consumption.

The OS output operates in either of two selectable modes: OS

comparator mode and OS interrupt mode. Its active state can be

selected as either HIGH or LOW. The fault queue that defines the

number of consecutive faults in order to activate the OS output is

programmable as well as the set-point limits.

The temperature register always stores an 11-bit 2’s complement

data giving a temperature resolution of 0.125 °C. This high

temperature resolution is particularly useful in applications of

measuring precisely the thermal drift or runaway.

The device is powered-up in normal operation mode with the OS in

comparator mode, temperature threshold of 80 °C and hysteresis of

75 °C, so that it can be used as a stand-alone thermostat with those

pre-defined temperature set points.

FEATURES

• Pin-for-pin replacement for industry standard LM75 and offers

improved temperature resolution of 0.125 °C and specification of

a single part over power supply range from 2.8 V to 5.5 V.

• Small 8-pin package types: SO8 and TSSOP8

• I2C-bus interface with up to 8 devices on the same bus

• Power supply range from 2.8 V to 5.5 V

• Temperatures range from –55 °C to +125 °C

• 11-bit ADC that offers a temperature resolution of 0.125 °C

• Temperature accuracy of:

±2 °C from –25 °C to +100 °C

±3 °C from –55 °C to +125 °C

• Programmable temperature threshold and hysteresis set points

• Supply current of 3.5 µA in shut-down mode for power

conservation

• Stand-alone operation as thermostat at power-up.

• ESD protection exceeds 2000 V HBM per JESD22-A114,

200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101

• Latch-up testing is done to JESDEC Standard JESD78 which

exceeds 100 mA

APPLICATIONS

• System thermal management

• Personal computers

• Electronics equipment

• Industrial controllers.

ORDERING INFORMATION

Tamb = –55 °C to +125 °C

TYPE NUMBER Topside mark

PACKAGE

NAME

DESCRIPTION

LM75AD

LM75A

SO8

plastic small outline package; 8 leads; body width 3.9 mm

LM75ADP

LM75A

TSSOP8 plastic thin shrink small outline package; 8 leads; body width 3 mm

VERSION

SOT96-1

SOT505-1

WATCHDOG™ is a trademark of National Semiconductor Corporation.

2004 Oct 05

2

Share Link: