LT1160 View Datasheet(PDF) - Linear Technology

Part Name

Description

Manufacturer

LT1160

Half-/Full-Bridge N-Channel Power MOSFET Drivers

Linear Technology 

LT1160/LT1162

PIN FUNCTIONS

LT1160

SV+ (Pin 1): Main Signal Supply. Must be closely decoupled

to the signal ground Pin 5.

IN TOP (Pin 2): Top Driver Input. Pin 2 is disabled when Pin

3 is high. A 3k input resistor followed by a 5V internal

clamp prevents saturation of the input transistors.

IN BOTTOM (Pin 3): Bottom Driver Input. Pin 3 is disabled

when Pin 2 is high. A 3k input resistor followed by a 5V

internal clamp prevents saturation of the input transistors.

UV OUT (Pin 4): Undervoltage Output. Open collector NPN

output which turns on when V + drops below the

undervoltage threshold.

SGND (Pin 5): Small Signal Ground. Must be routed

separately from other grounds to the system ground.

PGND (Pin 6): Bottom Driver Power Ground. Connects to

source of bottom N-channel MOSFET.

B GATE FB (Pin 8): Bottom Gate Feedback. Must connect

directly to the bottom power MOSFET gate. The top

MOSFET turn-on is inhibited until Pin 8 has discharged to

below 2.5V.

B GATE DR (Pin 9): Bottom Gate Drive. The high current

drive point for the bottom MOSFET. When a gate resistor

is used it is inserted between Pin 9 and the gate of the

MOSFET.

PV+ (Pin 10): Bottom Driver Supply. Must be connected to

the same supply as Pin 1.

T SOURCE (Pin 11): Top Driver Return. Connects to the

top MOSFET source and the low side of the bootstrap

capacitor.

T GATE FB (Pin 12): Top Gate Feedback. Must connect

directly to the top power MOSFET gate. The bottom

MOSFET turn-on is inhibited until V12 – V11 has discharged

to below 2.9V.

T GATE DR (Pin 13): Top Gate Drive. The high current drive

point for the top MOSFET. When a gate resistor is used it

is inserted between Pin 13 and the gate of the MOSFET.

BOOST (Pin 14): Top Driver Supply. Connects to the high

side of the bootstrap capacitor.

LT1162

SV+ (Pins 1, 7): Main Signal Supply. Must be closely

decoupled to ground Pins 5 and 11.

IN TOP (Pins 2, 8): Top Driver Input. The Input Top is

disabled when the Input Bottom is high. A 3k input resistor

followed by a 5V internal clamp prevents saturation of the

input transistors.

IN BOTTOM (Pins 3, 9): Bottom Driver Input. The Input

Bottom is disabled when the Input Top is high. A 3k input

resistor followed by a 5V internal clamp prevents satura-

tion of the input transistors.

UV OUT (Pins 4, 10): Undervoltage Output. Open collector

NPN output which turns on when V+ drops below the

undervoltage threshold.

GND (Pins 5, 11): Ground Connection.

B GATE FB (Pins 6, 12): Bottom Gate Feedback. Must

connect directly to the bottom power MOSFET gate. The

top MOSFET turn-on is inhibited until Bottom Gate Feed-

back pins have discharged to below 2.5V.

B GATE DR (Pins 13, 19): Bottom Gate Drive. The high

current drive point for the bottom MOSFET. When a gate

resistor is used it is inserted between the Bottom Gate

Drive pin and the gate of the MOSFET.

PV+ (Pins 14, 20): Bottom Driver Supply. Must be con-

nected to the same supply as Pins 1 and 7.

T SOURCE (Pins 15, 21): Top Driver Return. Connects to

the top MOSFET source and the low side of the bootstrap

capacitor.

T GATE FB (Pins 16, 22): Top Gate Feedback. Must

connect directly to the top power MOSFET gate. The

bottom MOSFET turn-on is inhibited until VTGF – VTSOURCE

has discharged to below 2.9V.

T GATE DR (Pins 17, 23): Top Gate Drive. The high current

drive point for the top MOSFET. When a gate resistor is

used it is inserted between the Top Gate Drive pin and the

gate of the MOSFET.

BOOST (Pins 18, 24): Top Driver Supply. Connects to the

high side of the bootstrap capacitor.

11602fb

6

Share Link: