GLS85LS1016B-M-C-FZJE-ND103 View Datasheet(PDF) - Unspecified
Part Name
Description
Manufacturer
GLS85LS1016B-M-C-FZJE-ND103 Datasheet PDF : 8 Pages
| |||
GLS85LS1002A/1004A/1008B/1016B/1032B/1064B
Industrial / Commercial Temp SATA NANDrive™
Features
Industry Standard Serial ATA (SATA) Host Interface
- SATA 1.5 Gb/s or SATA 3.0 Gb/s 1)
- ATA/ATAPI-8 compliant
- Supports 48-bit address feature set
Performance
- Sequential data read -
Up to 110 MByte/sec*
- Sequential data write -
Up to 60 MByte/sec*
* measured using 128 KByte transfer size
Power Management
- 3.3V and 1.2Vpower supply
- Host SATA interface power management
- Immediate disabling of unused circuitry
without host intervention
Power Specifications 2)
- Active mode:
820mW typical (GLS85LS1064B)
565mW typical (GLS85LS1032B)
440mW typical (GLS85LS1016B)
360mW typical (GLS85LS1008B)
360mW typical (GLS85LS1004A)
360mW typical (GLS85LS1002A)
- Idle / Standby mode: 210mW typical
- Sleep mode:
70mW typical
Fact Sheet 03.001
May 2014
Expanded Data Protection
- Added data security through user-selectable
protection zones
Integrated Voltage Detector
- Detects supply voltage fluctuations and
generates reset during power-up and power-
down to prevent inadvertent writes
Supports SMART Commands
20-Byte Serial Number
- Factory pre-programmed 10-Byte unique ID
- User-programmable 10-Byte ID
Robust Built-in ECC
NAND Configuration
- 2 bits per cell (MLC)
Temperature Range
- Commercial: 0°C to 70°C
- Industrial: -40°C to 85°C
FBGA package
- 14.0 mm x 24.0 mm x 1.95 mm, 145-ball,
1.0 mm ball pitch, FZJE
All Devices are RoHS Compliant
1) Current product revision supports SATA Revision 1.x with
host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s).
SATA 3.0 Gb/s refers to SATA Revision 2.x and will be
supported by our planned future product revisions.
2) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
Product Description
The GLS85LS1002A / 1004A / 1008B / 1016B /
1032B / 1064B Industrial Temperature and
Commercial Temperature SATA NANDrive™ devices
(referred to as “SATA NANDrive” in this datasheet)
are fully integrated solid state drives. They combine
an advanced Greenliant NAND controller and 2, 4, 8,
16, 32 or 64 GByte of NAND flash in a multi-chip
package. These products are ideal for embedded and
portable applications that require smaller form factor
and more reliable data storage.
SATA-interface solid state mass storage technology is
widely used in portable and industrial computers, set-
top boxes, multi-functional printers, point-of-sales
terminals, video and audio recorders, medical
instruments and car infotainment systems.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
The integrated NAND flash controller with built-in
advanced NAND management firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
SATA NANDrive devices are offered in a 145-ball
BGA, 1 mm ball pitch package.
These specifications are subject to change without notice.
© 2014 Greenliant Systems
1
05/09/2014
S71430-F
Share Link: 