74OL60113S View Datasheet(PDF) - Fairchild Semiconductor
Part Name
Description
Manufacturer
74OL60113S Datasheet PDF : 15 Pages
| |||
Electrical Characteristics (TA = 0°C to 70°C unless otherwise specified)
TTL Output 74OL6000, 74OL6001(2)
Test Conditions
Symbol
Parameter
74OL6000 74OL6001
74OL6000/01
Min. Typ.* Max. Units
VCCI Input Supply Voltage
4.5 5.0
5.5
V
VCCO Output Supply Voltage
4.5 5.0
5.5
V
VIH High-Level Input Voltage
2.0
V
VIL Low-Level Input Voltage
0.8
V
VIK Input Clamp Voltage
VCCI = 4.5V, II = -18mA
-1.2
V
IIH
High-Level Input Current
VCCI = 5.5V, VIH = 4.5V
1.0 40.0 µA
IIL
Low-Level Input Current
VCCI = 5.5V, VIL = 0.4V
-200.0 -400.0 µA
ICCIH Input Supply Current (HIGH)
VCCI = 5.5V, VIN = VIH
10.0 14.0 mA
ICCIL Input Supply Current (LOW)
VCCI = 5.5V, VIN = VIL
10.0 14.0 mA
VOH High-Level Output Voltage VIN = 2.0V VIN = 0.8V VCCI = 4.5V, VCCO = 4.5V, 2.4 3.0
V
IOH = -400µA
VOL Low-Level Output Voltage VIN = 0.8V VIN = 2.0V VCCI = 4.5V, VCCO = 4.5V,
IOL = 16mA
0.3
0.6
V
VCCI = 4.5V, VCCO = 4.5V,
0.5
IOL = 4mA
IOH
High-Level Output Current VIN = VIH VIN = VIL
VCCI = 4.5V, VCCO = 4.5V,
VOH = 2.4V
-8.0 -10.0 mA
IOL Low-Level Output Current VIN = 0.8 V VIN = 2.0V VCCI = 4.5V, VCCO = 4.5V, 16.0
mA
VOL = 0.6V
IOS
Short-Circuit Output Current VIN = VIH VIN = VIL
VCCI = 5.5V, VCCO = 5.5V, -5.0 -25.0 -40.0 mA
ICCOH Output Supply Current
(HIGH)
VIN = VIH VIN = VIL
VCCI = 5.5V, VO = VOH,
VCCO= 5.5V
9.0 15.0 mA
ICCOL Output Supply Current
(LOW)
VIN = VIL
VIN = VIH
VCCI = 5.5V, VO = VOL,
VCCO = 5.5V
8.0 12.0 mA
*All typical values are at TA=25°C
Switching Characteristics (TA = 25°C unless otherwise specified)
TTL Output 74OL6000, 74OL6001(2)
Symbol
Parameter
Test Conditions
tPHL Propagation Delay Time For Output Low VCCI = 5V, VCCO = 5V
Level
tPLH Propagation Delay Time For Output High
Level
tr
Output Rise Time For Output High Level
tf
Output Fall Time For Output Low Level
Min.
Typ.
60
70
45
5
Max. Units
100 ns
100 ns
ns
ns
Fig.
15, 17
15, 17
15, 17
15, 17
Note:
2. The VCCO and VCCI supply voltages to the device must each be bypassed by a 0.1µF capacitor or larger. This can
be either a ceramic or solid tantalum capacitor with good high frequency characteristics. Its purpose is to stabilize
the operation of the high-gain amplifiers. Failure to provide the bypass will impair the DC and switching properties.
The total lead length between capacitor and optocoupler should not exceed 1.5mm. See Fig. 20.
©2000 Fairchild Semiconductor Corporation
74OL60XX Rev. 1.0.4
5
www.fairchildsemi.com
Share Link: 